24AA64-SN Datasheet, PDF (3/44 Pages) Microchip Technology – 64K I2C™ Serial EEPROM

24AA64/24LC64/24FC64
TABLE 1-2: AC CHARACTERISTICS
AC CHARACTERISTICS
Electrical Characteristics:
Industrial (I):
VCC = +1.7V to 5.5V TA = -40°C to +85°C
Automotive (E): VCC = +1.7V to 5.5V TA = -40°C to 125°C
Param.
No.
Sym.
Characteristic
Min.
Max. Units
Conditions
1
FCLK Clock frequency
—
100
kHz 1.7V  VCC  2.5V
—
400
2.5V  VCC  5.5V
—
400
1.7V  VCC  2.5V 24FC64
—
1000
2.5V  VCC  5.5V 24FC64
2
THIGH Clock high time
4000
—
ns 1.7V  VCC  2.5V
600
—
2.5V  VCC  5.5V
600
—
1.7V  VCC  2.5V 24FC64
500
—
2.5V  VCC  5.5V 24FC64
3
TLOW Clock low time
4700
—
ns 1.7V  VCC  2.5V
1300
—
2.5V  VCC  5.5V
1300
—
1.7V  VCC  2.5V 24FC64
500
—
2.5V  VCC  5.5V 24FC64
4
TR
SDA and SCL rise time
(Note 1)
—
1000
ns 1.7V  VCC  2.5V
—
300
2.5V  VCC  5.5V
—
300
1.7V  VCC  5.5V 24FC64
5
TF
SDA and SCL fall time
(Note 1)
—
300
ns All except, 24FC64
—
100
1.7V  VCC  5.5V 24FC64
6
THD:STA Start condition hold time
4000
—
ns 1.7V  VCC  2.5V
600
—
2.5V  VCC  5.5V
600
—
1.7V  VCC  2.5V 24FC64
250
—
2.5V  VCC  5.5V 24FC64
7
TSU:STA Start condition setup time
4700
—
ns 1.7V  VCC  2.5V
600
—
2.5V  VCC  5.5V
600
—
1.7V  VCC  2.5V 24FC64
250
—
2.5V  VCC  5.5V 24FC64
8
THD:DAT Data input hold time
0
—
ns (Note 2)
9
TSU:DAT Data input setup time
250
—
ns 1.7V  VCC  2.5V
100
—
2.5V  VCC  5.5V
100
—
1.7V  VCC  5.5V 24FC64
10
TSU:STO Stop condition setup time
4000
—
ns 1.7 V  VCC  2.5V
600
—
2.5 V  VCC  5.5V
600
—
1.7V  VCC  2.5V 24FC64
250
—
2.5 V  VCC  5.5V 24FC64
11
TSU:WP WP setup time
4000
—
ns 1.7V  VCC  2.5V
600
—
2.5V  VCC  5.5V
600
—
1.7V  VCC  5.5V 24FC64
12
THD:WP WP hold time
4700
—
ns 1.7V  VCC  2.5V
1300
—
2.5V  VCC  5.5V
1300
—
1.7V  VCC  5.5V 24FC64
Note 1: Not 100% tested. CB = total capacitance of one bus line in pF.
2: As a transmitter, the device must provide an internal minimum delay time to bridge the undefined region
(minimum 300 ns) of the falling edge of SCL to avoid unintended generation of Start or Stop conditions.
3: The combined TSP and VHYS specifications are due to new Schmitt Trigger inputs, which provide improved
noise spike suppression. This eliminates the need for a TI specification for standard operation.
4: This parameter is not tested but ensured by characterization. For endurance estimates in a specific
application, please consult the Total Endurance™ Model, which can be obtained from Microchip’s web site
at www.microchip.com.
 1997-2012 Microchip Technology Inc.
DS21189T-page 3