PIC16F777-I Datasheet, PDF (215/276 Pages) Microchip Technology – 28/40/44-Pin, 8-Bit CMOS Flash Microcontrollers with 10-Bit A/D and nanoWatt Technology

PIC16F7X7
18.2 DC Characteristics: Power-Down and Supply Current
PIC16F737/747/767/777 (Industrial, Extended)
PIC16LF737/747/767/777 (Industrial) (Continued)
PIC16LF737/747/767/777
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
PIC16F737/747/767/777
(Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
Param
No.
Device
Typ Max Units
Conditions
Supply Current (IDD)^(2,3)
PIC16LF7X7 8
20 µA
-40°C
7
15 µA
+25°C
VDD = 2.0V
7
15 µA
+85°C
PIC16LF7X7 16 30 µA
14 25 µA
14 25 µA
All devices 32 40 µA
-40°C
+25°C
+85°C
-40°C
VDD = 3.0V
FOSC = 31.25 kHz
(RC_RUN mode,
Internal RC Oscillator)
29 35 µA
29 35 µA
+25°C
+85°C
VDD = 5.0V
Extended devices 35 45 µA
+125°C
PIC16LF7X7 132 160 µA
-40°C
126 155 µA
+25°C
VDD = 2.0V
126 155 µA
PIC16LF7X7 260 310 µA
230 300 µA
230 300 µA
All devices 560 690 µA
+85°C
-40°C
+25°C
+85°C
-40°C
VDD = 3.0V
FOSC = 1 MHz
(RC_RUN mode,
Internal RC Oscillator)
500 650 µA
500 650 µA
+25°C
+85°C
VDD = 5.0V
Extended devices 570 710 µA
+125°C
PIC16LF7X7 310 420 µA
300 410 µA
300 410 µA
-40°C
+25°C
+85°C
VDD = 2.0V
PIC16LF7X7 550 650 µA
530 620 µA
530 620 µA
All devices 1.2 1.5 mA
-40°C
+25°C
+85°C
-40°C
VDD = 3.0V
FOSC = 4 MHz
(RC_RUN mode,
Internal RC Oscillator)
1.1 1.4 mA
1.1 1.4 mA
+25°C
+85°C
VDD = 5.0V
Extended devices 1.3 1.6 mA
+125°C
Legend:
Note 1:
2:
3:
Shading of rows is to assist in readability of the table.
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that add delta
current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated
by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.
 2004 Microchip Technology Inc.
DS30498C-page 213