MCP111_05 Datasheet, PDF (2/26 Pages) Microchip Technology – Micropower Voltage Detector

MCP111/112
1.0 ELECTRICAL
CHARACTERISTICS
Absolute Maximum Ratings†
V_DD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.0V
Input current (V_DD) . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 mA
Output current (RST) . . . . . . . . . . . . . . . . . . . . . . . . . .10 mA
Rated Rise Time of V_DD . . . . . . . . . . . . . . . . . . . . . . 100V/µs
All inputs and outputs (except RST) w.r.t. V_SS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.6V to (V_DD + 1.0V)
RST output w.r.t. V_SS . . . . . . . . . . . . . . . . . . . -0.6V to 13.5V
Storage temperature . . . . . . . . . . . . . . . . . . . 65°C to + 150°C
Ambient temp. with power applied . . . . . . . -40°C to + 125°C
Maximum Junction temp. with power applied . . . . . . . . 150°C
ESD protection on all pins . . . . . . . . . . . . . . . . . . . . . . . . . ≥ 2 kV
† Notice: Stresses above those listed under “Maximum
Ratings” may cause permanent damage to the device. This is
a stress rating only and functional operation of the device at
those or any other conditions above those indicated in the
operational listings of this specification is not implied.
Exposure to maximum rating conditions for extended periods
may affect device reliability.
DC CHARACTERISTICS
Electrical Specifications: Unless otherwise indicated, all limits are specified for V_DD = 1V to 5.5V, R_PU = 100 kΩ (only MCP111),
T_A = -40°C to +125°C.
Parameters
Sym
Min
Typ Max Units
Conditions
Operating Voltage Range
Specified V_DD Value to V_OUT low
Operating Current
V_DD Trip Point
MCP1XX-195
V_DD
V_DD
I_DD
V_TRIP
MCP1XX-240
1.0
1.0
—
1.872
1.853
2.285
2.262
—
—
<1
1.900
1.900
2.320
2.320
5.5
1.75
1.929
1.948
2.355
2.378
V
V I _RST = 10 µA, V _RST < 0.2V
µA
V T_A = +25°C (Note 1)
V T_A = -40°C to +85°C (Note 2)
V T_A = +25°C (Note 1)
V Note 2
MCP1XX-270
2.591
2.564
2.630
2.630
2.670
2.696
V T_A = +25°C (Note 1)
V Note 2
MCP1XX-290
2.857
2.828
2.900
2.900
2.944
2.973
V T_A = +25°C (Note 1)
V Note 2
MCP1XX-300
2.886
2.857
2.930
2.930
2.974
3.003
V T_A = +25°C (Note 1)
V Note 2
MCP1XX-315
3.034
3.003
3.080
3.080
3.126
3.157
V T_A = +25°C (Note 1)
V Note 2
MCP1XX-450
4.314
4.271
4.380
4.380
4.446
4.490
V T_A = +25°C (Note 1)
V Note 2
MCP1XX-475
4.561
4.514
4.630
4.630
4.700
4.746
V T_A = +25°C (Note 1)
V Note 2
V_DD Trip Point Tempco
T_TPCO
—
±100
— ppm/°
C
Note 1:
2:
3:
4:
Trip point is ±1.5% from typical value.
Trip point is ±2.5% from typical value.
This specification allows this device to be used in PICmicro^® microcontroller applications that require the In-Circuit
Serial Programming™ (ICSP™) feature (see device-specific programming specifications for voltage requirements).
This specification DOES NOT allow a continuous high voltage to be present on the open-drain output pin (V_OUT). The
total time that the V_OUT pin can be above the maximum device operational voltage (5.5V) is 100 sec. Current into the
V_OUT pin should be limited to 2 mA. It is recommended that the device operational temperature be maintained between
0°C to 70°C (+25°C preferred). For additional information, please refer to Figure 2-28.
This parameter is established by characterization and is not 100% tested.
DS21889D-page 2
© 2005 Microchip Technology Inc.