PIC16C57-RC Datasheet, PDF (111/194 Pages) Microchip Technology – EPROM/ROM-Based 8-bit CMOS Microcontroller Series

PIC16C5X
15.4
DC Characteristics: PIC16C54A-04, 10, 20, PIC16LC54A-04, PIC16LV54A-02 (Commercial)
PIC16C54A-04I, 10I, 20I, PIC16LC54A-04I, PIC16LV54A-02I (Industrial)
PIC16C54A-04E, 10E, 20E, PIC16LC54A-04E (Extended)
DC CHARACTERISTICS
Standard Operating Conditions (unless otherwise specified)
Operating Temperature 0°C ≤ TA ≤ +70°C for commercial
–40°C ≤ TA ≤ +85°C for industrial
–20°C ≤ TA ≤ +85°C for industrial-PIC16LV54A-02I
–40°C ≤ TA ≤ +125°C for extended
Param
No.
Symbol
Characteristic
Min
Typ†
Max Units Conditions
D030
VIL Input Low Voltage
I/O ports
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
VSS
—
0.2 VDD
V Pin at hi-impedance
VSS
—
0.15 VDD V
VSS
—
0.15 VDD V
VSS
—
0.15 VDD V RC mode only⁽³⁾
VSS
—
0.3 VDD
XT, HS and LP modes
D040
VIH Input High Voltage
I/O ports
I/O ports
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
0.2 VDD + 1 —
2.0
—
0.85 VDD
—
0.85 VDD
—
0.85 VDD
—
0.7 VDD
—
VDD
V For all VDD⁽⁴⁾
VDD
V 4.0V < VDD ≤ 5.5V⁽⁴⁾
VDD
V
VDD
V
VDD
V RC mode only⁽³⁾
VDD
V XT, HS and LP modes
D050
VHYS Hysteresis of Schmitt
Trigger inputs
0.15 VDD*
—
D060
IIL Input Leakage Current^(1,2)
I/O ports
-1.0
0.5
MCLR
MCLR
T0CKI
OSC1
-5.0
—
—
0.5
-3.0
0.5
-3.0
0.5
—
+1.0
+5.0
+3.0
+3.0
—
V
For VDD ≤ 5.5V:
µA VSS ≤ VPIN ≤ VDD,
pin at hi-impedance
µA VPIN = VSS +0.25V
µA VPIN = VDD
µA VSS ≤ VPIN ≤ VDD
µA VSS ≤ VPIN ≤ VDD,
XT, HS and LP modes
D080
VOL
Output Low Voltage
I/O ports
OSC2/CLKOUT
VOH
Output High Voltage⁽²⁾
I/O ports
OSC2/CLKOUT
—
—
—
—
VDD - 0.7
—
VDD - 0.7
—
0.6
V IOL = 8.7 mA, VDD = 4.5V
0.6
V IOL = 1.6 mA, VDD = 4.5V,
RC mode only
—
V IOH = -5.4 mA, VDD = 4.5V
—
V IOH = -1.0 mA, VDD = 4.5V,
RC mode only
* These parameters are characterized but not tested.
† Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance only
and is not tested.
Note 1: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified levels
represent normal operating conditions. Higher leakage current may be measured at different input voltage.
2: Negative current is defined as coming out of the pin.
3: For the RC mode, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC16C5X be
driven with external clock in RC mode.
© 2002 Microchip Technology Inc.
Preliminary
DS30453D-page 109