PIC16F1526_13 Datasheet, PDF (1/387 Pages) Microchip Technology – 64-Pin Flash Microcontrollers with XLP Technology

PIC16(L)F1526/7
64-Pin Flash Microcontrollers with XLP Technology
High-Performance RISC CPU:
• C Compiler Optimized Architecture
• Only 49 Instructions
• Up to 28 Kbytes Linear Program Memory
Addressing
• Up to 1536 Bytes Linear Data Memory
Addressing
• Operating Speed:
- DC – 20 MHz clock input @ 2.5V
- DC – 16 MHz clock input @ 1.8V
- DC – 200 ns instruction cycle
• Interrupt Capability with Automatic Context
Saving
• 16-Level Deep Hardware Stack with Optional
Overflow/Underflow Reset
• Direct, Indirect and Relative Addressing modes:
- Two full 16-bit File Select Registers (FSRs)
- FSRs can read program and data memory
Flexible Oscillator Structure:
• 16 MHz Internal Oscillator Block:
- Software selectable frequency range from
16 MHz to 31 kHz
• 31 kHz Low-Power Internal Oscillator
• External Oscillator Block with:
- Four crystal/resonator modes up to 20 MHz
- Three external clock modes up to 20 MHz
• Fail-Safe Clock Monitor
- Allows for safe shutdown if peripheral clock
stops
• Two-Speed Oscillator Start-up
• Oscillator Start-up Timer (OST)
Special Microcontroller Features:
• Operating Voltage Range:
- 1.8V to 3.6V (PIC16LF1526/7)
- 2.3V to 5.5V (PIC16F1526/7)
• Self-Programmable under Software Control
• Power-on Reset (POR)
• Power-up Timer (PWRT)
• Programmable Low-Power Brown-Out Reset
(LPBOR)
• Extended Watch-Dog Timer (WDT):
- Programmable period from 1ms to 256s
• Programmable Code Protection
• In-Circuit Serial Programming™ (ICSP™) via two
pins
• In-Circuit Debug (ICD) via Two Pins
• Enhanced Low-Voltage Programming (LVP)
• Power-Saving Sleep mode
• 128 Bytes High-Endurance Flash
- 100,000 write Flash endurance (minimum)
Extreme Low-Power Management
PIC16LF1526/7 with XLP:
• Sleep mode: 20 nA @ 1.8V, typical
• Watchdog Timer: 300 nA @ 1.8V, typical
• Secondary Oscillator: 600 nA @ 32 kHz, 1.8V,
typical
Analog Features:
• Analog-to-Digital Converter (ADC):
- 10-bit resolution
- 30 external channels
- Two internal channels
- Fixed Voltage Reference (FVR) channel
- Temperature Indicator channel
- Auto acquisition capability
- Conversion available during Sleep
- Dedicated ADC RC oscillator
- Fixed Voltage Reference (FVR) as ADC
positive reference
• Voltage Reference module:
- Fixed Voltage Reference (FVR) with 1.024V,
2.048V and 4.096V output levels
- Low-Power Sleep mode
- Low-Power BOR (LPBOR)
Peripheral Features:
• 53 I/O Pins and 1 Input-only Pin:
- High current sink/source 25 mA/25 mA
- Individually programmable weak pull-ups
- Individually programmable
interrupt-on-change (IOC) pins
• Timer0: 8-Bit Timer/Counter with 8-Bit
Programmable Prescaler
• Enhanced Timer1, 3, 5:
- 16-bit timer/counter with prescaler
- External Gate Input mode
- Low-power 32 kHz secondary oscillator driver
• Timer2, 4, 6, 8, 10: 8-Bit Timer/Counter with 8-Bit
Period Register, Prescaler and Postscaler
• Ten Capture/Compare/PWM (CCP) modules:
- 16-bit Capture, 200 ns (max. resolution)
- 16-bit Compare, 200 ns (max. resolution)
- 10-bit PWM, 20 kHz @ 10 bits
(max. frequency)
• Two Master Synchronous Serial Ports (MSSPs)
with SPI and I²C^TM with:
- 7-bit address masking
- SMBus/PMBus^TM compatibility
- Auto-wake-up on start
• Two Enhanced Universal Synchronous
Asynchronous Receiver Transmitters (EUSART):
- RS-232, RS-485 and LIN compatible
- Auto-Baud Detect
 2011-2013 Microchip Technology Inc.
DS41458C-page 1