MCP2515_12 Datasheet, PDF (1/92 Pages) Microchip Technology – Stand-Alone CAN Controller with SPI Interface

MCP2515
Stand-Alone CAN Controller with SPI Interface
Features:
• Implements CAN V2.0B at 1 Mb/s:
- 0 – 8 byte length in the data field
- Standard and extended data and remote
frames
• Receive Buffers, Masks and Filters:
- Two receive buffers with prioritized message
storage
- Six 29-bit filters
- Two 29-bit masks
• Data Byte Filtering on the First Two Data Bytes
(applies to standard data frames)
• Three Transmit Buffers with Prioritization and
Abort Features
• High-Speed SPI Interface (10 MHz):
- SPI modes 0,0 and 1,1
• One-Shot mode Ensures Message Transmission
is Attempted Only One Time
• Clock Out Pin with Programmable Prescaler:
- Can be used as a clock source for other
device(s)
• Start-of-Frame (SOF) Signal is Available for
Monitoring the SOF Signal:
- Can be used for time-slot-based protocols
and/or bus diagnostics to detect early bus
degradation
• Interrupt Output Pin with Selectable Enables
• Buffer Full Output Pins Configurable as:
- Interrupt output for each receive buffer
- General purpose output
• Request-to-Send (RTS) Input Pins Individually
Configurable as:
- Control pins to request transmission for each
transmit buffer
- General purpose inputs
• Low-Power CMOS Technology:
- Operates from 2.7V – 5.5V
- 5 mA active current (typical)
- 1 µA standby current (typical) (Sleep mode)
• Temperature Ranges Supported:
- Industrial (I): -40°C to +85°C
- Extended (E): -40°C to +125°C
Description
Microchip Technology’s MCP2515 is a stand-alone
Controller Area Network (CAN) controller that
implements the CAN specification, version 2.0B. It is
capable of transmitting and receiving both standard
and extended data and remote frames. The MCP2515
has two acceptance masks and six acceptance filters
that are used to filter out unwanted messages, thereby
reducing the host MCU’s overhead. The MCP2515
interfaces with microcontrollers (MCUs) via an industry
standard Serial Peripheral Interface (SPI).
Package Types
18-Lead PDIP/SOIC _{TXCAN 1}
RXCAN 2
CLKOUT/SOF 3
TX0RTS ⁴
TX1RTS 5
TX2RTS 6
OSC2 7
OSC1 8
Vss 9
20-LEAD TSSOP
TXCAN ¹
RXCAN ²
CLKOUT/SOF ³
TX0RTS ⁴
TX1RTS ⁵
NC ⁶
TX2RTS ⁷
OSC2 ⁸
OSC1 ⁹
VSS 10
18 VDD
17 RESET
16 CS
15 SO
14 SI
13 SCK
12 INT
11 RX0BF
10 RX1BF
20 _VDD
19 _RESET
18 _CS
17 SO
16 _SI
15 NC
14 SCK
13 INT
12 RX0BF
11 RX1BF
MCP2515
20-Lead 4x4 QFN*
CLKOUT ₁
TX0RTS ₂
TX1RTS ₃
NC ₄
TX2RTS ₅
20 19 18 17 16
15 SO
14 SI
EP
21
13 NC
12 SCK
11 INT
6 7 8 9 10
* Includes Exposed Thermal
Pad (EP); see Table 1-1.
 2003-2012 Microchip Technology Inc.
DS21801G-page 1