DSPIC33EP512MU810 Datasheet, PDF (1/10 Pages) Microchip Technology – dsPIC33EP512MU810 and PIC24EP512GU810 100-pin TQFP to 100-pin Plug-In Module (PIM)

dsPIC33EP512MU810 and
PIC24EP512GU810
dsPIC33EP512MU810 and PIC24EP512GU810
100-pin TQFP to 100-pin Plug-In Module (PIM)
Information Sheet
OVERVIEW
The dsPIC33EP512MU810 and PIC24EP512GU810
PlMs (MA330025-1 and MA240025-1, respectively)
are designed to demonstrate the capabilities of the
dsPIC33EP512MU810 and PIC24EP512GU810
devices. The dsPIC33EP512MU810 is a high-
performance 16-bit Digital Signal Controller (DSC) and
the PIC24EP512GU810 is a high-performance 16-bit
Microcontroller (MCU). Both devices include a USB 2.0
OTG interface. Refer to Figure 1 for the device
schematics and Figure 2 for the PIM connector
schematics.
These PIMs can be used for USB as well as non-USB
applications by configuring jumpers on the PIM PC
board. This routing is intended to maximize the
compatibility of the PIM with the Explorer 16
Development Board (DM240001) and its related
PICtail™ Plus daughter boards. For non-USB
applications, jumpers J1 through J5 must be populated
across positions 1 and 2, while jumpers J6 through J10
should be populated. For USB applications, jumpers J1
through J5 must be populated across positions 2 and 3,
while jumpers J6 through J10 should not be populated.
Figure 3 shows the jumper locations.
Table 1 shows the mapping between the 100-pin PIM
interface board and the device pins when the jumpers
on the PIM are configured for USB applications.
Table 2 shows the mapping between the 100-pin PIM
interface board and the device pins when the jumpers
on the PIM are configured for non-USB applications.
In addition, the dsPIC33EP512MU810 PIM can be
used to control the Microchip MCLV (DM330021),
MCHV (DM330023) and MCSM (DM330022) motor
control development boards. The Microchip application
note AN1208 “Integrated Power Factor Correction
(PFC) and Sensorless Field Oriented Control (FOC)
System” (DS01208) requires that an optional zero Ohm
resistor to be installed at location R1.
TABLE 1: 100-PIN TQFP TO 100-PIN PIM FOR USB APPLICATIONS
Device
Pin #
dsPIC33EP512MU810 and
PIC24EP512GU810
Functional Description
PIM
Pin #
Device
Pin #
dsPIC33EP512MU810 and
PIC24EP512GU810
Functional Description
1 RP127/RG15
2 VDD
3 _{AN29/PWM3H/PMD5/RP85/RE5}
4 _{AN30/PWM4L/PMD6/RP86/RE6}
5 AN31/PWM4H/PMD7/RP87/RE7
6 _{AN16/PWM5L/RP49/RC1}
7 _{AN17/PWM5H/RP50/RC2}
8 AN18/PWM6L/RP51/RC3
9 _{AN19/PWM6H/RP52/RC4}
10 _{C1IND/SCK2/PMA5/RP118/RG6}
11 C1INC/SDI2/PMA4/RP119/RG7
12 _{C2IND/SDO2/PMA3/RP120/RG8}
13 _MCLR
14 C2INC/PMA2/RP121/RG9
15 _VSS
16 _VDD
17 TMS/RP16/RA0
18 _{AN20/RP88/RE8}
37 VDD
—
19 _{AN21/RP89/RE9}
2
20 AN5/C1INA/VBUSON/VBUSST/RP37/RB5
3
21 _{AN4/C1INB/USBOEN/RP36/RB4}
4
22 _{AN3/C2INA/VPIO/RP35/RB3}
5
23 AN2/C2INB/VMIO/RP34/RB2
6
24 _{PGEC3/AN1/RP33/RB1}
7
25 _{PGED3/AN0/RP32/RB0}
8
26 PGEC1/AN6/RP38/RB6
9
27 _{PGED1/AN7/RCV/RP39/RB7}
10
28 _VREF-/RA9
11
29 VREF+/RA10
12
30 _AVDD
13
31 _AVSS
14
32 AN8/PMA6/RP40/RB8
15
33 AN9/PMA7//RP41/RB9
16
34 AN10/CVREF/PMA13/RP42/RB10
17
35 AN11/PMA12/RP43/RB11
18
36 VSS
37
69 _{ASDA1/DPLN/RP73/RD9}
PIM
Pin #
19
96
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
69
© 2011 Microchip Technology Inc.
DS51886B-page 1