MIC5268_06 Datasheet, PDF (6/8 Pages) Micrel Semiconductor – 150mA μCap CMOS LDO Regulator w/Power Good

Micrel, Inc.
MIC5268
Application Information
Enable/Shutdown
The MIC5268 comes with an active-high enable pin that
allows the regulator to be disabled. Forcing the enable
pin low disables the regulator and sends it into a “zero”
off-mode-current state. In this state, current consumed
by the regulator goes nearly to zero. Forcing the enable
pin high enables the output voltage. This part is CMOS
and the enable pin cannot be left floating; a floating
enable pin may cause an indeterminate state on the
output.
Transient Response
The MIC5268 implements a unique output stage to
dramatically improve transient response recovery time.
The output is a totem-pole configuration with a P-
channel MOSFET pass device and an N-channel
MOSFET clamp. The N-channel clamp is a significantly
smaller device that prevents the output voltage from
overshooting when a heavy load is removed. This
feature helps to speed up the transient response by
significantly decreasing transient response recovery time
during the transition from heavy load (100mA) to light
load (100µA).
Input Capacitor
An input capacitor is not required for stability. A 1µF
input capacitor is recommended when the bulk ac supply
capacitance is more than 10 inches away from the
device, or when the supply is a battery.
Active Shutdown
The MIC5268 also features an active shutdown clamp,
which is an N-channel MOSFET that turns on when the
device is disabled. This allows the output capacitor and
load to discharge, de-energizing the load.
Output Capacitor
The MIC5268 requires an output capacitor for stability.
The design requires 1µF or greater on the output to
maintain stability. The capacitor can be a low-ESR
ceramic chip capacitor. The MIC5268 has been
designed to work specifically with the low-cost, small
chip capacitors. Tantalum capacitors can also be used
for improved capacitance overtemperature. The value of
the capacitor can be increased without bound.
X7R dielectric ceramic capacitors are recommended
because of their temperature performance. X7R-type
capacitors change capacitance by 15% over their
operating temperature range and are the most stable
type of ceramic capacitors. Z5U and Y5V dielectric
capacitors change value by as much 50% and 60%
respectively over their operating temperature ranges. To
use a ceramic chip capacitor withY5V dielectric, the
value must be much higher than an X7Rceramic or a
tantalum capacitor to ensure the same minimum
capacitance value over the operating temperature range.
Tantalum capacitors have a very stable dielectric (10%
over their operating temperature range) and can also be
used with this device.
Power Good
The power good output is an open-drain output. It is
designed essentially to work as a power-on reset
generator once the regulated voltage was up and/or a
fault condition. The output of the power good drives low
when a fault condition AND an undervoltage detection
occurs. The power good output comes back up once the
output has reached 97% of its nominal value and a 1ms
to 5ms delay has passed. See Timing Diagram.
The MIC5268’s internal circuit intelligently monitors
overcurrent, overtemperature and dropout conditions
and ORs these outputs together indicate some fault
condition. This output is fed into an on-board delay
circuitry that drives the open drain transistor to indicate a
fault.
Thermal Considerations
The MIC5268 is designed to provide 150mA of
continuous current in a very small package. Maximum
power dissipation can be calculated based on the output
current and the voltage drop across the part. To
determine the maximum power dissipation of the
package, use the junction-to-ambient thermal resistance
of the device and the following basic equation:
P_D(max)
=
⎜⎜⎝⎛
T_J(max) −
θ _JA
T_A
⎟⎟⎠⎞
T_J(max) is the maximum junction temperature of the die,
125°C, and T_A is the ambient operating temperature. θ_JA
is layout dependent; Table 1 shows examples of
junction-to-ambient thermal resistance for the MIC5268.
Package
SOT-23-5 (M5)
θ_JA Recommended
Minimum Footprint
235°C/W
θ_JA 1” Square
Copper Clad
185°C/W
θ_JC
145°C/W
Table 1. Thermal Resistance
The actual power dissipation of the regulator circuit can
be determined using the equation:
P_D = (V_IN – V_OUT) I_OUT + V_IN I_GND
Substituting P_D(max) for P_D and solving for the operating
conditions that are critical to the application will give the
maximum operating conditions for the regulator circuit.
For example, when operating the MIC5268-1.2BM5 at
50°C with a minimum footprint layout, the maximum
input voltage for a set output current can be determined
as follows:
P_D(max)
=
⎜⎛ ^{125°C − 50°C} ⎟⎞
⎝ ^235°C ⎠
P_D(max) = 315mW
September 2006
6
M9999-091506