MIC5330 Datasheet, PDF (5/10 Pages) Micrel Semiconductor – Dual, 300mA UCap LDO in 2mm x 2mm MLF

Micrel, Inc.
MIC5330
Absolute Maximum Ratings⁽¹⁾
Supply Voltage (V_IN) .....................................0V to +6V
Enable Input Voltage (V_EN)...........................0V to +6V
Power Dissipation...........................Internally Limited⁽³⁾
Lead Temperature (soldering, 3sec ...................260°C
Storage Temperature (T_S) ................. -65°C to +150°C
ESD Rating⁽⁴⁾ .........................................................2kV
Operating Ratings⁽²⁾
Supply voltage (V_IN)............................... +2.3V to +5.5V
Enable Input Voltage (V_EN).............................. 0V to V_IN
Junction Temperature ......................... -40°C to +125°C
Junction Thermal Resistance
MLF-8 (θ_JA) ............................................... 90°C/W
Electrical Characteristics⁽⁵⁾
V_IN = EN1 = EN2 = V_OUT + 1.0V; higher of the two regulator outputs, I_OUTLDO1 = I_OUTLDO2 = 100µA; C_OUT1 = C_OUT2 = 1µF;
C_BYP = 0.1µF; T_J = 25°C, bold values indicate –40°C ≤ T_J ≤ +125°C, unless noted.
Parameter
Conditions
Min Typ Max Units
Output Voltage Accuracy
Variation from nominal V_OUT
Variation from nominal V_OUT; –40°C to +125°C
-2.0
+2.0 %
-3.0
+3.0 %
Line Regulation
V_IN = V_OUT + 1V to 5.5V; I_OUT = 100µA
0.02 0.3 %/V
0.6 %/V
Load Regulation
I_OUT = 100µA to 300mA
0.5
%
Dropout Voltage (Note 6)
I_OUT = 100µA
I_OUT = 100mA
I_OUT = 150mA
I_OUT = 300mA
0.1
mV
25
75
mV
35 100 mV
75 200 mV
Ground Current
EN1 = High; EN2 = Low; I_OUT = 100µA to 300mA
EN1 = Low; EN2 = High; I_OUT = 100µA to 300mA
EN1 = EN2 = High; I_OUT1 = 300mA, I_OUT2 = 300mA
85 120 µA
85 120 µA
150 200 µA
Ground Current in Shutdown EN1 = EN2 = 0V
0.01 2
µA
Ripple Rejection
f = 1kHz; C_OUT = 1.0µF; C_BYP = 0.1µF
f = 20kHz; C_OUT = 1.0µF; C_BYP = 0.1µF
70
dB
65
dB
Current Limit
V_OUT = 0V
350 550 950 mA
Output Voltage Noise
C_OUT = 1.0µF; C_BYP = 0.1µF; 10Hz to 100kHz
30
µV_RMS
Enable Inputs (EN1 / EN2)
Enable Input Voltage
Logic Low
0.2
V
Logic High
1.1
V
Enable Input Current
V_IL ≤ 0.2V
0.01
µA
V_IH ≥ 1.0V
0.01
µA
Turn-on Time (See Timing Diagram)
Turn-on Time (LDO1 and 2) C_OUT = 1.0µF; C_BYP = 0.01µF
30
100
µs
Notes:
1. Exceeding the absolute maximum rating may damage the device.
2. The device is not guaranteed to function outside its operating rating.
3. The maximum allowable power dissipation of any T_A (ambient temperature) is P_D(max) = (T_J(max) – T_A) / θ_JA. Exceeding the maximum allowable
power dissipation will result in excessive die temperature, and the regulator will go into thermal shutdown.
4. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5k in series with 100pF.
5. Specification for packaged product only.
6. Dropout voltage is defined as the input-to-output differential at which the output voltage drops 2% below its nominal V_OUT. For outputs below
2.3V, the dropout voltage is the input-to-output differential with the minimum input voltage 2.3V.
August 2006
5
M9999-080306