MIC5232_08 Datasheet, PDF (4/10 Pages) Micrel Semiconductor – 10mA Ultra-Low Quiescent Current μCap LDO

Micrel, Inc.
Absolute Maximum Ratings⁽¹⁾
Supply Input Voltage (V_IN) ................................0V to 8V
Enable Input Voltage (V_EN)...............................0V to 8V
Power Dissipation (P_D) .................... Internally Limited⁽³⁾
Junction Temperature (T_J).................. –40°C to +125°C
Storage Temperature (T_S) .................. –65°C to +150°C
Lead Temperature (soldering, 5 sec.) ................. 260°C
ESD Rating⁽⁴⁾......................................................... ±2kV
MIC5232
Operating Ratings⁽²⁾
Supply voltage (V_IN) ...................................... 2.7V to 7V
Enable Input voltage (V_EN) ...............................0V to V_IN
Thermal Resistance
TSOT-23-5 (θ_JA)......................................... 235°C/W
MLF-6 (θ_JA) .................................................. 90°C/W
Electrical Characteristics⁽⁵⁾
V_IN = V_OUT + 1.0V, C_OUT = 0.47µF, I_OUT = 100µA, T_J = 25°C, bold values indicate –40°C to +125°C, unless noted.
Parameter
Conditions
Min Typ Max Units
Output Voltage Accuracy
Variation from nominal V_OUT
-2.0
+2.0
%
Variation from nominal V_OUT; -40C to +125C
-3.0
+3.0
%
Output Voltage Temp.
Coefficient
40
ppm/C
Line Regulation
V_IN = V_OUT +1V to7V;
0.02 0.25 %/V
Load Regulation
I_OUT = 10µA to 10mA
Dropout Voltage⁽⁶⁾
Ground Pin Current
Ground Pin Current in
Shutdown
Current Limit
Reverse Current (V_OUT > V_IN)
Ripple Rejection
Output Voltage Noise
Enable Input
Enable Input Voltage
Enable Input Current
Turn-on Time
I_OUT = 100µA
I_OUT = 10mA
I_OUT = 10µA
V_EN < 0.18V
V_OUT = 0V
V_OUT = V_IN + 1V
f = 10Hz
f = 1kHz
C_OUT =0.47µF; 10Hz to 100kHz
Logic Low (Regulator Shutdown)
Logic High (Regulator Enabled)
VIL < 0.18V (Regulator Shutdown)
VIH > 1.4V (Regulator Enabled)
C_OUT = 0.47µF⁽⁷⁾
0.2 1.0
%
1.5
%
60
mV
100 300 mV
1.8 3
µA
0.1 1.5
µA
70 120 mA
0.02 1
µA
55
dB
35
dB
400
µVrms
0.18
V
1.4
V
1
nA
1
nA
0.75 1.5
ms
Notes:
1. Exceeding the absolute maximum rating may damage the device.
2. The device is not guaranteed to function outside its operating rating.
3. The maximum allowable power dissipation of any T_A (ambient temperature) is P_D(max) = T_J(max) – T_A) / θ_JA. Exceeding the maximum allowable
power dissipation will result in excessive die temperature.
4. Devices are ESD sensitive. Handling precautions recommended.
5. Specification for packaged product only.
6. Dropout voltage is defined as the input-to-output differential at which the output voltage drops 2% below its nominal V_OUT. For outputs below
2.7V, dropout voltage is the input-to-output differential with the minimum input voltage 2.7V.
7. Turn-on time is measured from 10% of the positive edge of the enable signal to 90% of the rising edge of the output voltage of the regulator.
September 2008
4
M9999-090508-C