English
Language : 

MIC2563A_04 Datasheet, PDF (4/12 Pages) Micrel Semiconductor – Dual-Slot PCMCIA/CardBus Power Controller
◁
MIC2563A
Micrel
Symbol
Parameter
Condition
Min Typ Max Units
VPP Switching Time (See Figure 1) continued
t14
Output Turn-Off Delay Time(4, 5)
t15
t16
t11
Output Turn-Off Fall Time(4)
t12
t13
VCC Output
ICCSC
Short Circuit Current Limit
RO
Switch Resistance
VCC Switching Time (See Figure 2)
t1
Output Turn-On Delay Time(6)
t2
t3
Output Rise Time(6)
t4
t7
Output Turn-Off Delay(6, 7)
t8
t5
Output Fall Time(6)
t6
Power Supply
VPP OUT = 3.3V to Hi-Z
VPP OUT = 5V to Hi-Z
VPP OUT = 12V to Hi-Z
VPP OUT = 90% to 10% of 3.3V
VPP OUT = 90% to 10% of 5V
VPP OUT = 90% to 10% of 12V
VCC OUT = 0
Select VCC OUT = 3.3V
ICC OUT = –1A (Sourcing)
Select VCC OUT = 5V
ICC OUT = –1A (Sourcing)
Select VCC OUT = clamped to ground
ICC OUT = 0.1mA (Sinking)
VCC OUT = 0V to 10% of 3.3V
VCC OUT = 0V to 10% of 5.0V
VCC OUT = 10% to 90% of 3.3V
VCC OUT = 10% to 90% of 5V
VCC OUT = 3.3V
VCC OUT = 5V
VCC OUT = 90% to 10% of 3.3V
VCC OUT = 90% to 10% of 5.0V
200 1000 ns
200 1000 ns
200 1000 ns
50 1000 ns
50 1000 ns
300 2000 ns
1
1.5
A
100 150 mΩ
70
100 mΩ
500 3900 Ω
300 1500 µs
750 3000 µs
200 700 2500 µs
200 1500 6000 µs
2.4
8
ms
2.8
8
ms
100 240 1000 µs
100 600 2000 µs
ICC5
VCC5 IN Supply Current (5V)
ICC3
IPP IN
VCC3 IN Supply Current (3.3V)(8)
VPP IN Supply Current (12V)(9)
VCC5
Operating Input Voltage (5V)
VCC3
Operating Input Voltage (3.3V)(8)
VPP IN
Operating Input Voltage (12V)
Thermal Shutdown
VCC OUT = 5V or 3.3V, ICC OUT = 0
VCC OUT = 0V (Sleep Mode)
VCC OUT = 5V or 3.3V, ICC OUT = 0
VCC OUT = 0V (Sleep Mode)
VPP OUT = 3.3V or 5V, IPP OUT = 0
VPP OUT = Hi-Z, 0 or VPP
VCC5 IN not required for operation
VPP IN not required for operation(10)
8
50
µA
0.2
10
µA
40
100
µA
0.1
10
µA
0.3
4
µA
0.3
4
µA
5.0
6
V
3.0
3.3
6
V
12.0 14.5
V
TSD
Thermal Shutdown Temperature
130
°C
Notes:
4. RL = 100Ω connected to ground.
5. Delay from commanding Hi-Z or 0V to beginning slope. Does not apply to current limit or overtemperature shutdown conditions.
6. RL = 10Ω connected to ground.
7. Delay from commanding Hi-Z or 0V to beginning slope. Does not apply to current limit or overtemperature shutdown conditions.
8. The MIC2563A uses VCC3 IN for operation. For single 5V supply systems, connect 5V to both VCC3 IN and VCC5 IN. See “Applications Information”
section for further details.
9. VPP IN is not required for operation.
10. VPP IN must be either high impedance or greater than or approximately equal to the highest voltage VCC in the system. For example, if both 3.3V
and 5V are connected to the MIC2563A, VPP IN must be either 5V, 12V, or high impedance.
M9999-110503
4
March 2004
 ▷