MIC2525 Datasheet, PDF (3/12 Pages) Micrel Semiconductor – USB Power Control Switch Not Recommended for New Designs

MIC2525
Absolute Maximum Ratings (Note 1)
Supply Voltage (V_IN) ..................................................... +6V
Fault Flag Voltage (V_FLG) .............................................. +6V
Fault Flag Current (I_FLG) ............................................ 50mA
Output Voltage (V_OUT) .................................................. +6V
Output Current (I_OUT) ............................... Internally Limited
Control Input (V_EN) ......................................... –0.3V to 12V
Storage Temperature (T_S) ....................... –65°C to +150°C
Lead Temperature (Soldering 5 sec.) ....................... 260°C
ESD Rating, Note 3 ...................................................... 2kV
Micrel
Operating Ratings (Note 2)
Supply Voltage (V_IN) ...................................... +3V to +5.5V
Ambient Operating Temperature (T_A) ........ –40°C to +85°C
Thermal Resistance
SOIC (θ_JA) ......................................................... 120°C/W
DIP(θ_JA) ............................................................. 130°C/W
Electrical Characteristics
V_IN = +5V; T_A = 25°C; unless noted.
Parameter
Condition
Min Typ Max Units
Supply Current
Note 4, switch off, OUT = open
0.75
5
µA
Note 4, switch on, OUT = open
110 160
µA
Enable Input Threshold
low-to-high transition
2.1
2.4
V
high-to-low transition, Note 4
0.8
1.9
V
Enable Input Current
Enable Input Capacitance
V_EN = 0V to 5.5V
–1 ±0.01 1
µA
1
pF
Switch Resistance
Output Turn-On Delay
Output Turn-On Rise Time
Output Turnoff Delay
Output Turnoff Fall Time
Output Leakage Current
V_IN = 5V, I_OUT = 500mA
V_IN = 3.3V, I_OUT = 500mA
R_L = 10Ω each output
R_L = 10Ω each output
R_L = 10Ω each output
R_L = 10Ω each output
output disabled
100 140 mΩ
140 180 mΩ
0.5
ms
1
ms
1
20
µs
1
20
µs
10
µA
Continuous Load Current
0.5
A
Short-Circuit Current Limit
Current-Limit Threshold
Overtemperature Shutdown
Threshold
Error Flag Output Resistance
Error Flag Off Current
UVLO Threshold
enable into load, V_OUT = 4.0V
ramped load applied to enabled output, V_OUT ≤ 4.0V, Note 5
T_J increasing
T_J decreasing
V_IN = 5V, I_L = 10mA
V_IN = 3.3V, I_L = 10mA
V_FLAG = 5V
V_IN = increasing
V_IN = decreasing
0.5 0.75 1.25
A
1.6
2.2
A
135
°C
125
°C
10
25
Ω
15
40
Ω
0.01
1
µA
2.5
V
2.3
V
Note 1.
Note 2.
Note 3.
Note 4.
Note 5.
Exceeding the absolute maximum rating may damage the device.
The device is not guaranteed to function outside its operating rating.
Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5k in series with 100pF.
Off is ≤ 0.8V and on is ≥ 2.4V for the MIC2525-1. Off is ≥ 2.4V and on is ≤ 0.8V for the MIC2525-2. The enable input has approximately
200mV of hysteresis. See control threshold charts.
See “Functional Characteristics: Current-Limit Response” photo.
January 2000
3
MIC2525