MIC23153 Datasheet, PDF (12/18 Pages) Micrel Semiconductor – 4MHz PWM 2A Buck Regulator with HyperLight Load™ and Power Good

Micrel Inc.
Compensation
The MIC23153 is designed to be stable with a 0.47µH to
2.2µH inductor with a 4.7µF ceramic (X5R) output
capacitor.
Duty Cycle
The typical maximum duty cycle of the MIC23153 is
80%.
Efficiency Considerations
Efficiency is defined as the amount of useful output
power, divided by the amount of power supplied.
Efficiency
%
=
⎜⎜⎝⎛
V_OUT
V_IN
× I_OUT
× I_IN
⎟⎟⎠⎞
× 100
Maintaining high efficiency serves two purposes. It
reduces power dissipation in the power supply, reducing
the need for heat sinks and thermal design
considerations and it reduces consumption of current for
battery-powered applications. Reduced current draw
from a battery increases the devices operating time and
is critical in hand held devices.
There are two types of losses in switching converters;
DC losses and switching losses. DC losses are simply
the power dissipation of I²R. Power is dissipated in the
high side switch during the on cycle. Power loss is equal
to the high side MOSFET R_DSON multiplied by the Switch
Current squared. During the off cycle, the low side N-
channel MOSFET conducts, also dissipating power.
Device operating current also reduces efficiency. The
product of the quiescent (operating) current and the
supply voltage represents another DC loss. The current
required driving the gates on and off at a constant 4MHz
frequency and the switching transitions make up the
switching losses.
Efficiency v s. Output Current
V_OUT = 1.8V @ 25°C
1.00 V_IN = 3V
0.90
0.80
0.70
0.60
VIN = 5V
VIN = 3.6V
0.50
0.40
0.30
0.20
0.10
0.00001
0.001
0.1
10
OUT PUT CURRENT (A)
Figure 2. Efficiency Under Load
The figure above shows an efficiency curve. From no
load to 100mA, efficiency losses are dominated by
quiescent current losses, gate drive and transition
losses. By using the HyperLight Load™ mode, the
MIC23153 is able to maintain high efficiency at low
MIC23153
output currents.
Over 100mA, efficiency loss is dominated by MOSFET
R_DSON and inductor losses. Higher input supply voltages
will increase the Gate-to-Source threshold on the
internal MOSFETs, thereby reducing the internal R_DSON.
This improves efficiency by reducing DC losses in the
device. All but the inductor losses are inherent to the
device. In which case, inductor selection becomes
increasingly critical in efficiency calculations. As the
inductors are reduced in size, the DC resistance (DCR)
can become quite significant. The DCR losses can be
calculated as follows:
P_DCR = I_OUT2 x DCR
From that, the loss in efficiency due to inductor
resistance can be calculated as follows:
Efficiency
Loss
=
⎡
⎢¹
⎢⎣
−
⎜⎜⎝⎛
V_OUT × I_OUT
V_OUT × I_OUT + P_DCR
⎟⎟⎠⎞⎥⎥⎦⎤ ^{× 100}
Efficiency loss due to DCR is minimal at light loads and
gains significance as the load is increased. Inductor
selection becomes a trade-off between efficiency and
size in this case.
HyperLight Load™ Mode
MIC23153 uses a minimum on and off time proprietary
control loop (patented by Micrel). When the output
voltage falls below the regulation threshold, the error
comparator begins a switching cycle that turns the
PMOS on and keeps it on for the duration of the
minimum-on-time. This increases the output voltage. If
the output voltage is over the regulation threshold, then
the error comparator turns the PMOS off for a minimum-
off-time until the output drops below the threshold. The
NMOS acts as an ideal rectifier that conducts when the
PMOS is off. Using a NMOS switch instead of a diode
allows for lower voltage drop across the switching device
when it is on. The asynchronous switching combination
between the PMOS and the NMOS allows the control
loop to work in discontinuous mode for light load
operations. In discontinuous mode, the MIC23153 works
in pulse frequency modulation (PFM) to regulate the
output. As the output current increases, the off-time
decreases, thus provides more energy to the output.
This switching scheme improves the efficiency of
MIC23153 during light load currents by only switching
when it is needed. As the load current increases, the
MIC23153 goes into continuous conduction mode (CCM)
and switches at a frequency centered at 4MHz. The
equation to calculate the load when the MIC23153 goes
into continuous conduction mode may be approximated
by the following formula:
I_LOAD
> _{⎜⎜⎝⎛} ^(VIN
− V_OUT
2L × f
)
×
D
⎟⎟⎠⎞
As shown in the previous equation, the load at which the
MIC23153 transitions from HyperLight Load™ mode to
December 2009
12
M9999-121409-A