MIC39150_09 Datasheet, PDF (10/14 Pages) Micrel Semiconductor – 1.5A, Low-Voltage Low-Dropout Regulator

Micrel, Inc.
Application Information
The MIC39150/1/2 are high-performance, low-dropout
voltage regulators suitable for moderate to high-current
voltage regulator applications. Its 500mV dropout
voltage at full load and overtemperature makes it
especially valuable in battery-powered systems and as
high-efficiency noise filters in post-regulator applications.
Unlike older NPN-pass transistor designs, where the
minimum dropout voltage is limited by the base-to-
emitter voltage drop and collector-to-emitter saturation
voltage, dropout performance of the PNP output of these
devices is limited only by the low V_CE saturation voltage.
A trade-off for the low dropout voltage is a varying base
drive requirement. Micrel’s Super βeta PNP^® process
reduces this drive requirement to only 2% to 5% of the
load current. The MIC39150/1/2 regulators are fully
protected from damage due to fault conditions. Current
limiting is provided. This limiting is linear; output current
during overload conditions is constant. Thermal
shutdown disables the device when the die temperature
exceeds the maximum safe operating temperature.
Transient protection allows device (and load) survival
even when the input voltage spikes above and below
nominal. The output structure of these regulators allows
voltages in excess of the desired output voltage to be
applied without reverse current flow.
Thermal Design
Linear regulators are simple to use. The most
complicated design parameters to consider are thermal
characteristics. Thermal design requires the following
application-specific parameters:
• Maximum ambient temperature (T_A)
• Output Current (I_OUT)
• Output Voltage (V_OUT)
• Input Voltage (V_IN)
• Ground Current (I_GND)
First, calculate the power dissipation of the regulator
from these numbers and the device parameters from this
datasheet.
P_D = (V_IN − V_OUT ) I_OUT + V_IN I_GND
where the ground current is approximated by using
numbers from the “Electrical Characteristics” or “Typical
Characteristics.” Then the heat sink thermal resistance is
determined with this formula:
( ) θ_SA
=
T_J(max) − T_A
P_D
−
θ _JC + θ_CS
Where T_J(max) ≤ 125°C and θ_CS is between 0° and 2°C/W.
The heat sink may be significantly reduced in
applications where the minimum input voltage is known
and is large compared with the dropout voltage. Use a
series input resistor to drop excessive voltage and
October 2009
MIC39150/39151/39152
distribute the heat between this resistor and the
regulator. The low dropout properties of Micrel Super
βeta PNP^® regulators allow significant reductions in
regulator power dissipation and the associated heat sink
without compromising performance. When this technique
is employed, a capacitor of at least 1µF is needed
directly between the input and regulator ground.
Refer to Application Note 9 for further details and
examples on thermal design and heat sink specification.
With no heat sink in the application, calculate the
junction temperature to determine the maximum power
dissipation that will be allowed before exceeding the
maximum junction temperature of the MIC39152. The
maximum power allowed can be calculated using the
thermal resistance (θ_JA) of the TO-252 (D-Pak) adhering
to the following criteria for the PCB design: 2 oz. copper
and 100mm² copper area for the MIC39152.
For example, given an expected maximum ambient
temperature (T_A) of 75°C with V_IN = 2.25V, V_OUT = 1.75V,
and I_OUT = 1.5A, first calculate the expected P_D using
Equation (1);
P_D = (2.25V – 1.75V)1.5A + (2.25V)(0.017A) = 0.788W
Next, calcualte the junction temperature for the expected
power dissipation.
T_J = (θ_JA × P_D) + T_A = (56°C/W × 0.788W) + 75°C
= 119.14°C
Now determine the maximum power dissipation allowed
that would not exceed the IC’s maximum junction
temperature (125°C) without the use of a heat sink by
P_D(MAX) = (T_J(MAX) – T_A)/θ_JA = (125°C – 75°C)/(56°C/W)
= 0.893W
V_IN
C_IN
MIC39150-x.x
IN OUT
V_{OU T}
GND
C_{OU T}
Figure 1. Capacitor Requirements
Output Capacitor
The MIC39150/1/2 requires an output capacitor to
maintain stability and improve transient response. See
Figure 1. Proper capacitor selection is important to
ensure proper operation. TheMIC39150/1/2 output
capacitor selection is dependent upon the ESR
(equivalent series resistance) of the output capacitor to
maintain stability. When the output capacitor is 10µF or
greater, the output capacitor should have an ESR less
than 2Ω. This will improve transient response as well as
10
M9999-102309-A