PEVA Datasheet, PDF (1/2 Pages) MERITEK ELECTRONICS CORPORATION – Conductive Polymer Aluminum Solid Capacitors (V Chip)

Conductive Polymer Aluminum
Solid Capacitors (V Chip)
PEVA Series
RoHS
FEATURES
 Standard SMD type
 Rated voltage: 2.5VDC ~25VDC
 Endurance: 2000hours at 105ºC
 Suitable for DC-DC converters, Voltage regulators and decoupling applications.
MERITEK
SPECIFICATIONS
Item
Characteristic
Category Temperature Range
-55ºC ~ +105C
Rated Voltage Range
Surge Voltage
Rated voltage x 1.15V
2.5VDC ~ 25VDC
at +105C
Capacitance Tolerance
M=±20%
at 120Hz, 20ºC
Leakage Current
Shall not exceed values shown in standard ratings
at 20ºC after 2 minutes
Dissipation Factor ( tan  )
0.12 (max)
at 120Hz, 20ºC
Temperature Stability
Impedance change
Z(-55ºC)/Z(+20ºC)≤1.25
at -55C, 100kHz
Z(+105ºC)/Z(+20ºC)≤1.25
at +105C, 100kHz
Endurance
Appearance: no significant damage
Capacitance change: ≤ ±20% of the initial value
DF(tanδ): ≤ 150% of the initial specified value
ESR: ≤ 150% of the initial specified value
Leakage current: ≤ the initial specified value
The specifications shall be satisfied when
the capacitors are restored to 20ºC after
the rated voltage is applied for 2000hours
at 105ºC
Damp Heat, Steady State
Appearance: no significant damage
Capacitance change: ≤ ±20% of the initial value
DF(tanδ): ≤ 150% of the initial specified value
ESR: ≤ 150% of the initial specified value
Leakage current: ≤ the initial specified value
The specifications shall be satisfied when
the capacitors are restored to 20ºC after
subjecting them to store at 60ºC, 90%~
95% R.H. for 1000hours, without DC
applied.
Surge Voltage
Appearance: no significant damage
The capacitors shall be subjected to
Capacitance change: ≤ ±20% of the initial value 1,000 cycles each consisting of charge
DF(tanδ): ≤ 150% of the initial specified value
with the surge voltages specified at
ESR: ≤ 150% of the initial specified value
105ºC for 30 seconds through a
Leakage current: ≤ the initial specified value
protective resistor (R=1kΩ) and
discharge for 5 minutes 30 seconds
NOTE:
If any doubt arises, measure the leakage current after following voltage treatment -
Voltage treatment: DC rated voltage is applied to the capacitors for 60 minutes at 105ºC
DIMENSIONS (mm)
Size code
BD+0.5 (max)
TH±0.2
BW±0.2
BL±0.2
TL±0.2
EW
EG±0.2
0506
5.0
5.8
5.3
5.3
6.0
0.5~0.8
1.4
0604
6.3
4.3
6.6
6.6
7.3
0.5~0.8
2.1
0606
6.3
5.8
6.6
6.6
7.3
0.5~0.8
2.1
0807
8.0
6.8
8.3
8.3
9.0
0.5~0.8
2.9
0810
8.0
9.7
8.3
8.3
9.0
0.8~1.1
2.9
Rev. 7