PE5P Datasheet, PDF (1/6 Pages) MERITEK ELECTRONICS CORPORATION – Conductive Polymer Aluminum Solid Capacitors (Radial Type)

Conductive Polymer Aluminum
Solid Capacitors (Radial Type)
FEATURES
 Low ESR
 Rated voltage: 6.3VDC, 16VDC
 Endurance: 5000hours at 105ºC
PART NUMBER SYSTEM
PE5P 16V 331 M 0809
PE5P Series
RoHS
MERITEK
Meritek Series
Rated Voltage
Rated Capacitance
Express in micro farad(uF), First two digits
are significant figures, Third digit denotes
number of zeros. ‘R’ denotes decimal point
for values less than 10uF.
Capacitance Tolerance: ±20%
Case Size: (D) Diameter x (L) Length in mm
SPECIFICATIONS
Each measurement shall be conducted at a temperature of 15ºC to 35ºC, and relative humidity of 45% to 85%. Furthermore, these
measurements shall be preferably conducted at a temperature of 20ºC±2ºC, and relative humidity of 60% to 70%, while the
capacitors shall be kept enough time in the measuring temperature.
Parameter
Standard
Category temperature range -55ºC~+105ºC
Capacitance tolerance
±20%(M)
capacitance measured at 120Hz±10%
Low Temperature Stability
Impedance ratio
Performance
Impedance at 100kHz at -55ºC±3ºC or -25ºC±3ºC
Z(-25ºC)/Z(+20ºC)
≤ 1.15
Z(-55ºC)/Z(+20ºC)
≤ 1.25
Endurance
A capacitor shall be subjected to a temperature of 105ºC±2ºC with test voltage applied for a period of 5,000+72/-0
hours and take out from the above condition to a temperature of 20ºC. After this test, that capacitor shall meet the
characteristics as following. Besides, the applied voltage shall increase up from 0V to test voltage step by step
(maximum 5 minutes), and the impedance of the source shall be equal to about 3Ω/V.
Characteristics
Appearance
Capacitance change
tanδ
ESR
Leakage current
Performance
No significant damage
≤ ±20% of the initial value
≤ 150% of the initial specified value
≤ 150% of the initial specified value
≤ the initial specified value
Rated voltage (Vr)
6.3V
16V
Surge voltage¹
7.2V
18.4V
Capacitance
220uF
680uF
820uF
330uF
Leakage current²
277uA
857uA
1,033uA
1,056uA
tanδ³
0.1
0.1
0.1
0.1
ESR⁴
15mΩ, max
12mΩ, max
8mΩ, max
13mΩ, max
Rated ripple current⁵
3.16Arms
3.5Arms
4.7Arms
4.7Arms
Dimension
6x6
6x8
6x10
8x9
NOTE:
1. Surge Voltage = Vr x 1.15
2. DC rated voltage shall be applied between anode and cathode lead wire terminations of a capacitor through 1kΩ protective
resistance, and the leakage current shall be less than or equal to standard ratings after 2 minutes with the voltage reaching the rated
value at 20ºC±2ºC.
If leakage current is doubtful, measure it after performing voltage treatment, which shall contain the following steps:
(1) Applied DC rated voltage to the capacitors for 60 minutes at 105ºC±2ºC
(2) Cooled down to room temperature with applying voltage.
(3) Discharged through a resistor of approximately 1Ω/V.
3. measured at 120Hz±10%
4. ESR measured under the following conditions, shall be less than or equal to standard ratings
Equipment
Agilent Technology 4263B or equivalent
Test Fixture
Agilent Technology 16047E or equivalent
Compensation
Short and Open compensation would be required.
Short correction is performed using the shorting.
plate made of 0.5 thickness copper plate with gold
coating
Signal Level
500mV
Frequency
100kHz
Measurement Point
Point of lead wire within 1mm from the body