PE5K Datasheet, PDF (1/2 Pages) MERITEK ELECTRONICS CORPORATION – Conductive Polymer Aluminum Solid Capacitors (Radial type)

Conductive Polymer Aluminum
Solid Capacitors (Radial type)
PE5K Series
RoHS
FEATURES
 Super low ESR, high ripple current capability
 Rated voltage: 2.5VDC ~16VDC
 Endurance: 5000hours at 105ºC
 Suitable for DC-DC converters, voltage regulators and decoupling applications.
MERITEK
SPECIFICATIONS
Item
Characteristic
Category Temperature Range
Rated Voltage Range
Surge Voltage
Capacitance Tolerance
Rated voltage x 1.15V
M=±20%
-55ºC ~ +105C
2.5VDC ~ 16VDC
at +105C
at 120Hz, 20ºC
Leakage Current
Dissipation Factor ( tan  )
Shall not exceed values shown in standard ratings
0.1 (max)
at 20ºC after 2 minutes
at 120Hz, 20ºC
Temperature Stability
Impedance change
Z(-55ºC)/Z(+20ºC)≤1.25
at -55C, 100kHz
Z(+105ºC)/Z(+20ºC)≤1.25
at +105C, 100kHz
Endurance
Appearance: no significant damage
Capacitance change: ≤ ±20% of the initial value
DF(tanδ): ≤ 150% of the initial specified value
ESR: ≤ 150% of the initial specified value
Leakage current: ≤ the initial specified value
The specifications shall be satisfied when
the capacitors are restored to 20ºC after
the rated voltage is applied for 5000hours
at 105ºC
Damp Heat, Steady State
Appearance: no significant damage
Capacitance change: ≤ ±20% of the initial value
DF(tanδ): ≤ 150% of the initial specified value
ESR: ≤ 150% of the initial specified value
Leakage current: ≤ the initial specified value
The specifications shall be satisfied when
the capacitors are restored to 20ºC after
subjecting them to store at 60ºC, 90%~
95% R.H. for 1000hours, without DC
applied.
Surge Voltage
Appearance: no significant damage
Capacitance change: ≤ ±20% of the initial value
DF(tanδ): ≤ 150% of the initial specified value
ESR: ≤ 150% of the initial specified value
Leakage current: ≤ the initial specified value
The capacitors shall be subjected to
1,000 cycles each consisting of charge
with the surge voltages specified at
105ºC for 30 seconds through a
protective resistor (R=1kΩ) and
discharge for 5 minutes 30 seconds
NOTE:
If any doubt arises, measure the leakage current after following voltage treatment -
Voltage treatment: DC rated voltage is applied to the capacitors for 60 minutes at 105ºC
DIMENSIONS (mm)
Size code
BD+0.5 (max)
BL,(max)
Φd±0.05
LS±0.4
LL±0.3
0509
5.0
9.0
0.5
2.0
3.2
0606
6.3
6.0
0.45
2.5
3.2
0609
6.3
9.0
0.6
2.5
3.2
0809
8.0
9.0
0.6
3.5
3.2
0812
8.0
12.0
0.6
3.5
3.2
1012
10.0
12.0
0.6
5.0
3.2
Rev. 7