OC31E Datasheet, PDF (1/2 Pages) Mercury United Electronics Inc – Mercury OC31E is 36.2x27.2 mm 5 pin solder sealed metal pacakge

OCXO (Oven Controlled Crystal Oscillators) +5.0 V; +12 V
OC31E Series
50 ohm Load Sine Wave
MERCURY
Since 1973
Mercury OC31E is 36.2x27.2 mm 5 pin solder sealed metal pacakge
with 25.4x17.8 mm pin-to-pin spacing high stability low aging OCXO.
Besides standard AT cut crystal, users can also choose SC cut crystal
for better performance. HCMOS square wave output is available as OC31T series.
OC30E series: Same package size as OC31E but with different pin configurations.
General Specifications ( 10 MHz at+25°C, at specified Vcc and +2.5 V Vcon)
Output Wave Form
Sine wave. Wave form code is “E”
Frequency Range
10 MHz ~100.0 MHz
Type of Crystal Cut Used
AT-cut. Use “A” for crystal code or SC-cut: use “S” for crystal code.
SC has better performance but higher cost. See technical note TN-031.
Supply Voltage (Vcc)
+5.0 V _D.C ±5% (voltage code is “5”); +12.0 V _D.C ±5% (voltage code is “12”)
Initial Calibration Tolerance
±0.5 ppm max. at time of shipment; Vcon=+2.5V
Operating Temperature Range
(custom spec. on request)
Best Stability
For AT crystal
For SC crystal
0°C to +60°C
±0.03 ppm
±0.01 ppm
-20°C to +70°C
±0.08 ppm
±0.02 ppm
-40°C to +85°C
±0.2 ppm
±0.03 ppm
Aging (after 72 hours of AT:±3 ppb max./day; ±0.5 ppm max./first year;±3 ppm max. over 10 years.
continuous operation) SC: ±2 ppb max./day; ±0.1 ppm max./first year;±0.5 ppm max. over 10 years.
Supply Voltage ±5% Variation ±20 ppb max.
Load ±5% variation
±20 ppb max.
Warm-up time (at +25°C)
Freq. Deviation Range
AT: 3 minutes max. Within ±0.5 ppm of its reference frequency.
SC: 1 minute max. Within ±0.1 ppm of its reference frequency.
AT: ±5 ppm min. ±20 ppm max.; Referenced to fo at +25°C and over
SC: ±0.5 ppm min, ±2 ppm max. operating temperature range.
Control Voltage Range
2.5 V ± 2.0 V
Transfer Function
Positive: Increasing control voltage increases output frequency.
Input Impedance
100 K ohms min.
EFC Linearity
±10% max.
Power Power Dissipation (at +25°C) 1.2 Watts max. at steady-state; 3.5 Watts max. at turn-on.
Output Level
+3 dBm typical; +8 dBm max. with 50Ω load
Harmonic
-30 dBc min.
Output
Spurious
Reference Voltage
Phase
Noise
Offset
10 MHz AT-cut XTAL
10 MHz SC-cut XTAL
-75 dBc min.
+4.0 V _D.C.±0.3 V _D.C. or custom.
1 Hz
10 Hz
100 Hz
-75 dBc
-100 dBc -130 dBc
-85 dBc
-120 dBc -140 dBc
1 KHz
-140 dBc
-145 dBc
10 KHz
-150 dBc
-150 dBc
Storage Temperature
-55°C to +125°C
Shock
2000 G’s, 0.3 ms ½ sine
Vibration
10 to 2000 Hz / 10 G’s
MERCURY www.mercury-crystal.com
Taiwan: TEL [phone], FAX [phone], e-mail: [e-mail]
U.S.A.: TEL [phone], FAX [phone], e-mail: [e-mail]
MERCURY
Page 1 of 2
Date: July 20, 2006
Rev. 0