ODLV-45 Datasheet, PDF (2/6 Pages) Mean Well Enterprises Co., Ltd. – 45W PWM Output LED Driver

45W PWM Output LED Driver
ODLV-45 series
SPECIFICATION
MODEL
ODLV-45 -12
ODLV-45 -24
ODLV-45 -36
ODLV-45 -48
ODLV-45 -60
DC VOLTAGE
12V
24V
36V
RATED CURRENT
3.0A
1.88A
1.25A
RATED POWER
36W
45.12W
45W
DIMMING RANGE
OUTPUT
VOLTAGE TOLERANCE
0~100%
±10%
PWM FREQUENCY (Typ.)
1KHz(±20%)
SETUP TIME Note.3
500ms / 230VAC 1200ms/115VAC
AUXILIARY DC OUTPUT Note.4 Nominal 12V(deviation 11.4~12.6)@50mA for A-Type only
VOLTAGE RANGE Note.2 ^{90 ~ 295VAC 127 ~ 417VDC}
(Please refer to "STATIC CHARACTERISTIC" section)
FREQUENCY RANGE 47 ~ 63Hz
48V
0.94A
45.12W
60V
0.75A
45W
PF>0.95/115VAC, PF>0.92/230VAC, PF>0.9/277VAC@full load
POWER FACTOR (Typ.)
(Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)
INPUT
THD< 20%(@load≧60%/115VAC,230VAC; @load≧75%/277VAC)
TOTAL HARMONIC DISTORTION
(Please refer to “TOTAL HARMONIC DISTORTION” section)
EFFICIENCY (Typ.)
84%
86%
88%
88%
90%
AC CURRENT (Typ.)
0.6A / 115VAC 0.4A / 230VAC 0.3A / 277VAC
INRUSH CURRENT(Typ.) COLD START 30A(twidth=150μs measured at 50% Ipeak) at 230VAC; Per NEMA 410
MAX. No. of PSUs on 16A
CIRCUIT BREAKER
32 units (circuit breaker of type B) / 32 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT <0.75mA / 277VAC
NO LOAD POWER CONSUMPTION <0.5W for Blank-Type, <1.2W for A-Type
SHORT CIRCUIT
Shut down O/P voltage, re-power on to recovery
PROTECTION
OVER CURRENT
105 ~ 115%
Protection type : Hiccup mode, recovers automatically after fault condition is removed
WORKING TEMP.
Tcase=-20 ~ +85℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)
MAX. CASE TEMP.
Tcase=+85℃
WORKING HUMIDITY
ENVIRONMENT
20 ~ 90% RH non-condensing
STORAGE TEMP., HUMIDITY -40 ~ +80℃, 10 ~ 95% RH
TEMP. COEFFICIENT
±0.03%/℃ (0 ~ 50℃)
VIBRATION
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
SAFETY STANDARDS
UL8750(type"HL"),CSA C22.2 NO.250.13-12;ENEC EN61347-1 & EN61347-2-13 independent, EN62384,GB19510.1,GB19510.14;
IP67 approved
WITHSTAND VOLTAGE I/P-O/P:3.75KVAC
SAFETY &
ISOLATION RESISTANCE I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH
EMC
EMC EMISSION
Compliance to EN55015, EN61000-3-2 Class C (@load≧60%) ; EN61000-3-3,GB17743,GB17625.1
EMC IMMUNITY
Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, light industry level(surge immunity:Line-Line:1KV)
MTBF
388.02K hrs min. MIL-HDBK-217F (25℃)
OTHERS DIMENSION
111*77*28.5mm (L*W*H)
PACKING
0.42Kg;24pcs/11Kg/ 0.72CUFT
NOTE
1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25℃ of ambient temperature.
2. De-rating may be needed under low input voltages. Please refer to “STATIC CHARACTERISTIC” sections for details.
3. Length of set up time is measured at cold first start. Turning ON/OFF the driver may lead to increase of the set up time.
4. There is no design of short circuit protection for the Auxiliary DC output; this function can not be used when dimming input terminals(DIM+,DIM-)
are short circuit or when it is no load or short circuit at output(Vo+,Vo-).
5. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be
affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
File Name:ODLV-45-SPEC 2017-07-21