HBG-60 Datasheet, PDF (2/6 Pages) Mean Well Enterprises Co., Ltd. – CONSTANT CURRENT MODE OUTPUT

60W Constant Current Mode LED Driver
HBG-60 series
SPECIFICATION
MODEL
OUTPUT
HBG-60-1050
HBG-60-1400
RATED CURRENT
RATED POWER
CONSTANT CURRENT REGION Note.2
OPEN CIRCUIT VOLTAGE(max.)
CURRENT ADJ. RANGE
CURRENT RIPPLE
1050mA
57.75W
37 ~ 55V
60V
680 ~ 1050mA
20% max. @rated current
1400mA
60.2W
28 ~ 43V
50V
910 ~ 1400mA
CURRENT TOLERANCE
±5.0%
SET UP TIME Note.4
500ms / 230VAC 1200ms / 115VAC
VOLTAGE RANGE
90 ~ 295VAC 127 ~ 417VDC
Note.3 _{(Please refer to "STATIC CHARACTERISTIC" section)}
FREQUENCY RANGE
47 ~ 63Hz
POWER FACTOR
PF>0.97/115VAC, PF>0.95/230VAC, PF>0.9/277VAC@full load
(Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)
HBG-60-2100
2100mA
60.9W
19 ~ 29V
35V
1360mA ~ 2100mA
INPUT
TOTAL HARMONIC DISTORTION
THD< 20%(@load≧65%/115VC,230VAC; @load≧75%/277VAC)
(Please refer to “TOTAL HARMONIC DISTORTION(THD)” section)
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INRUSH CURRENT (Typ.)
MAX. No. of PSUs on 16A
CIRCUIT BREAKER
90%
89%
89%
0.7A/115VAC 0.4A/230VAC 0.3A/277VAC
COLD START 45A(twidth=100μs measured at 50% Ipeak) at 230VAC; Per NEMA 410
28 units (circuit breaker of type B) / 32 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT
<0.75mA / 277VAC
OVER CURRENT
PROTECTION _{OVER TEMPERATURE}
Hiccup mode, recovers automatically after fault condition is removed
Shut down o/p voltage, re-power on to recover
WORKING TEMP.
Tcase=-40 ~ +85℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)
MAX. CASE TEMP.
Tcase=+85℃
WORKING HUMIDITY
20 ~ 95% RH non-condensing
ENVIRONMENT
STORAGE TEMP., HUMIDITY
-40 ~ +80℃, 10 ~ 95% RH
TEMP. COEFFICIENT
±0.03%/℃ (0 ~ 60℃)
VIBRATION
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
SAFETY STANDARDS
UL8750, CSA C22.2 No. 250.13-12, ENEC EN61347-1,EN61347-2-13 independent, EN62384; GB19510.14, GB19510.1 approved
WITHSTAND VOLTAGE
SAFETY &
ISOLATION RESISTANCE
EMC
EMC EMISSION Note.8
I/P-O/P:3.75KVAC
I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH
Compliance to EN55015, GB17743, GB17625.1, EN61000-3-2 Class C (@load≧65%) ; EN61000-3-3
EMC IMMUNITY
Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, EN55024, light industry level(surge immunity:Line-Line:2KV)
MTBF
1504.1K hrs min. Telcordia SR-332 (Bellcore) ; 452Khrs min. MIL-HDBK-217F (25℃)
OTHERS DIMENSION
ψ110mm * 60.5mm (D * H)
PACKING
0.5Kg; 20pcs/ 11Kg/ 0.94CUFT
NOTE
1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25℃ of ambient temperature.
2. Please refer to "DRIVING METHODS OF LED MODULE".
3. De-rating may be needed under low input voltages. Please refer to “STATIC CHARACTERISTIC” sections for details.
4. Length of set up time is measured at cold first start. Turning ON/OFF the driver may lead to increase of the set up time.
5. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected
by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
6.To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED driver can only be used behind a switch without permanently
connected to the mains.
7. This series meets the typical life expectancy of >50,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 80℃ or less.
8. Please refer to the warranty statement on MEAN WELL's website at http://www.meanwell.com
File Name:HBG-60-SPEC 2016-06-16