HBG-100P Datasheet, PDF (2/7 Pages) Mean Well Enterprises Co., Ltd. – CONSTANT CURRENT MODE OUTPUT

100W Constant Current Mode LED Driver
HBG-100P series
SPECIFICATION
MODEL
OUTPUT
HBG-100P-36
HBG-100P-48
RATED CURRENT
2.7A
2A
RATED POWER
97.2W
96W
CONSTANT CURRENT REGION Note.2 21.6 ~ 36V
28.8 ~ 48V
OPEN CIRCUIT VOLTAGE(max.) 37V
49V
Adjustable for A-Type only (via built-in potentiometer)
CURRENT ADJ. RANGE _{1.62 ~ 2.7A}
1.2 ~ 2A
CURRENT RIPPLE
5.0% max. @rated current
CURRENT TOLERANCE ±5.0%
SET UP TIME Note.4
2000ms / 115VAC 500ms / 230VAC
VOLTAGE RANGE
90 ~ 305VAC 127 ~ 431VDC
Note.3 _{(Please refer to "STATIC CHARACTERISTIC" section)}
FREQUENCY RANGE
POWER FACTOR
47 ~ 63Hz
PF≧0.96/115VAC, PF≧0.96/230VAC, PF≧0.94/277VAC@full load
(Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)
HBG-100P-60
1.6A
96W
36 ~ 60V
62V
1.0 ~ 1.6A
THD< 20%(@load≧60%/115VC,230VAC; @load≧75%/277VAC)
TOTAL HARMONIC DISTORTION _{(Please refer to “TOTAL HARMONIC DISTORTION(THD)” section)}
INPUT
EFFICIENCY (Typ.)
AC CURRENT
INRUSH CURRENT(Typ.)
91%
91%
91.5%
1.1A / 115VAC 0.5A / 230VAC 0.45A / 277VAC
COLD START 60A(twidth=415μs measured at 50% Ipeak) at 230VAC; Per NEMA 410
MAX. No. of PSUs on 16A
CIRCUIT BREAKER
4 units (circuit breaker of type B) / 8 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT
<0.75mA / 277VAC
OVER CURRENT
PROTECTION
OVER VOLTAGE
95 ~ 108%
Constant current limiting, recovers automatically after fault condition is removed
41 ~ 49V
54 ~ 63V
65 ~ 75V
Shut down o/p voltage, re-power on to recovery
OVER TEMPERATURE
WORKING TEMP.
Shut down o/p voltage, re-power on to recovery
Ta=-40 ~ +45℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)
WORKING HUMIDITY
20 ~ 95% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +80℃, 10 ~ 95% RH
TEMP. COEFFICIENT
±0.03%/℃ (0 ~ 45℃)
VIBRATION
10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes
SAFETY STANDARDS
SAFETY & ^{WITHSTAND VOLTAGE}
EMC
ISOLATION RESISTANCE
EMC EMISSION
UL8750,CSA C22.2 No.250.13-12; ENEC EN61347-1,EN61347-2-13,EN62384, GB19510.1,GB19510.14 approved
I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH
Compliance to EN55015, EN61000-3-2 Class C (@load ≧60%) ; EN61000-3-3, GB17743, GB17625.1
EMC IMMUNITY
MTBF
Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547,light industry level(surge immunity:Line-Earth:4KV,Line-Line:2KV)
346.8Khrs min. MIL-HDBK-217F (25℃)
OTHERS DIMENSION
PACKING
Refer to mechanical specification
0.3Kg; 45pcs/14.5Kg/1.60CUFT
NOTE
1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25℃ of ambient temperature.
2. Please refer to "DRIVING METHODS OF LED MODULE".
3. De-rating may be needed under low input voltages. Please refer to “STATIC CHARACTERISTIC” sections for details.
4. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time.
5. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
6. This series meets the typical life expectancy of >50,000 hours of operation when Ta is about 45℃ or less.
7. Please refer to the warranty statement on MEAN WELL's website at http://www.meanwell.com
File Name:HBG-100P-SPEC 2016-05-03