EPS-45S Datasheet, PDF (2/4 Pages) Mean Well Enterprises Co., Ltd. – 45W Single Output Switching Power Supply

45W Single Output Switching Power Supply _{EPS-45S series}
SPECIFICATION
ORDER NO.
EPS-45S-3.3 EPS-45S-5 EPS-45S-7.5 EPS-45S-12 EPS-45S-15
DC VOLTAGE
3.3V
5V
7.5V
12V
15V
RATED CURRENT
8A
8A
5.4A
3.8A
3A
CURRENT RANGE
0 ~ 8.8A
0 ~ 8.8A
0 ~ 5.95A
0 ~ 4.18A
0 ~ 3.3A
RATED POWER
26.4W
40W
40.5W
45.6W
45W
OUTPUT PEAK LOAD(10sec.) Note.2 29W
RIPPLE & NOISE (max.) Note.3 80mVp-p
44W
80mVp-p
44.6W
80mVp-p
50.2W
120mVp-p
49.5W
150mVp-p
VOLTAGE ADJ.RANGE
3.1~3.6V
VOLTAGE TOLERANCE Note.4 ±2.0%
LINE REGULATION
±0.5%
LOAD REGULATION
±2.0%
4.7~5.5V
±2.0%
±0.5%
±2.0%
7.12~8.3V
±2.0%
±0.5%
±2.0%
11.4~13.2V
±2.0%
±0.5%
±2.0%
13.5~16.5V
±1.0%
±0.5%
±1.0%
SETUP, RISE TIME
500ms, 30ms / 230VAC 500ms, 30ms / 115VAC at full load
HOLD UP TIME (Typ.)
30ms / 230VAC 12ms / 115VAC at full load
VOLTAGE RANGE Note.5 80 ~ 264VAC
FREQUENCY RANGE
47 ~ 63Hz
INPUT EFFICIENCY (Typ.)
80%
83%
85%
88%
89%
AC CURRENT (Typ.)
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT(max.)
1.2A / 115VAC 1A / 230VAC
СOLD STAR 30A/115VAC 60A/230VAC
0.25mA/264VAC
OVERLOAD
115 ~ 150% rated output power
Protection type : Hiccup mode, recovers automatically after fault condition is removed
PROTECTION
OVER VOLTAGE
3.8~5V
5.7~6.8V
8.62~11.3V 13.8~16.2V
Protection type : Shut down o/p voltage, re-power on to recover
17.25~20.3V
WORKING TEMP.
-30 ~ +70℃ (Refer to "Derating Curve")
WORKING HUMIDITY
ENVIRONMENT STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
20% ~ 90% RH non-condensing
-40 ~ +85℃, 10 ~ 95% RH
±0.03% / ℃ (0 ~ 50℃)
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
SAFETY STANDARDS
SAFETY & ^{ISOLATION LEVEL}
EMC
WITHSTAND VOLTAGE
(Note. 7) _{ISOLATION RESISTANCE}
UL60950-1, TUV EN60950-1 approved
Primary-Secondary: 2xMOPP
I/P-O/P: 3KVAC
I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH
EMC EMISSION
Compliance to EN55022(CISPR22) Class B, EN61000-3-2,3
EMC IMMUNITY
Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, Heavy industry Level criteria A
OTHERS
MTBF
DIMENSION
PACKING
726.2Khrs min. MIL-HDBK-217(25℃)
76.2*50.8*24mm or 3" * 2" *0.945" inch (L*W*H)
0.11Kg; 120pcs/14.2Kg/0.97CUFT
EPS-45S-24
24V
1.9A
0 ~ 2.1A
45.6W
50.2W
240mVp-p
22.8~27.6V
±1.0%
±0.5%
±1.0%
90%
28.4~32.4V
EPS-45S-48
48V
0.94A
0 ~ 1.03A
45.1W
49.4W
300mVp-p
45.6~52.8V
±1.0%
±0.5%
±1.0%
91%
55.2~64.8V
NOTE
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
2. 33% Duty cycle maximum within every 30 seconds. Average output power should not exceed the rated power.
3. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
4. Tolerance : includes set up tolerance, line regulation and load regulation.
5. Derating may be needed under low input voltages. Please check the derating curve for more details.
6. Touch current was measured from primary input to DC output.
7. The ambient temperature derating of 5℃/1000m is needed for operating altitude greater than 2000m (6500ft).
8. The power supply is considered a component which will be installed into a final equipment. "All the EMC tests are been executed by mounting
the unit on a 360mm*360mm metal plate with 1mm of thickness." The final equipment must be re-confirmed that it still meets EMC directives.
For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.”
(as available on http://www.meanwell.com)
File Name:EPS-45S-SPEC 2015-12-10