SD-150_11 Datasheet, PDF (1/2 Pages) Mean Well Enterprises Co., Ltd. – 150W Single Output DC-DC Converter

150W Single Output DC-DC Converter
SD-150 series
Features :
2:1 wide input range
Protections: Short circuit / Overload / Over voltage
1500VAC I/O isolation
Built-in EMI filter, low ripple noise
100% full load burn-in test
24V and 48V input voltage design refer to LVD
Low cost
High reliability
2 years warranty
SPECIFICATION
(for D type only)
MODEL
SD-150B-12
SD-150C-12
SD-150D-12
SD-150B-24
SD-150C-24
SD-150D-24
DC VOLTAGE
12V
24V
RATED CURRENT
12.5A
6.3A
CURRENT RANGE
0 ~ 12.5A
0 ~ 6.3A
RATED POWER
150W
151.2W
OUTPUT
RIPPLE & NOISE (max.) Note.2 120mVp-p
VOLTAGE ADJ. RANGE
11 ~ 16VDC
VOLTAGE TOLERANCE Note.3 1.0%
LINE REGULATION
0.5%
150mVp-p
23 ~ 30VDC
1.0%
0.3%
LOAD REGULATION
0.5%
0.3%
SETUP, RISE TIME
2s, 50ms(only D mode) at full load
HOLD UP TIME (Typ.)
24ms(only D mode) at full load
INPUT
VOLTAGE RANGE
EFFICIENCY (Typ.)
DC CURRENT (Typ.)
INRUSH CURRENT (Typ.)
B:19 ~ 36VDC
75%
6.8A/24V
D:22.5A/96VDC
C:36 ~ 72VDC
77%
3.4A/48V
D:72 ~144VDC or 85 ~ 132VAC
79%
77%
2.7A/96V
6.8A/24V
80%
3.4A/48V
82%
2.7A/96V
LEAKAGE CURRENT
<0.75mA / 120VAC (SD-150D)
OVERLOAD
PROTECTION
OVER VOLTAGE
WORKING TEMP.
WORKING HUMIDITY
ENVIRONMENT STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
SAFETY &
EMC
(Note 4)
SAFETY STANDARDS
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
EMC EMISSION
105 ~ 135% rated output power
Protection type : Hiccup mode, recovers automatically after fault condition is removed
16.8V ~ 20V/10% LOAD
31.5 ~ 37.5V/10% LOAD
Protection type : Hiccup mode, recovers automatically after fault condition is removed
-10 ~ +60 (Refer to "Derating Curve")
20 ~ 90% RH non-condensing
-20 ~ +85 , 10 ~ 95% RH
0.03%/ (0 ~ 50
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
IEC60950-1 CB approved by TUV (for D type only)
I/P-O/P:1.5KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH
Compliance to EN55022 (CISPR22) Class B
OTHERS
NOTE
EMC IMMUNITY
Compliance to EN61000-4-2,3,4,6,8, light industry level, criteria A
MTBF
296.2K hrs min.(SD-150B) 289.9K hrs min.(SD-150C) 289K Hrs min.(SD-150D) MIL-HDBK-217F (25 )
DIMENSION
199*110*50mm (L*W*H)
PACKING
0.86Kg; 16pcs/14.5Kg/0.95CUFT
1. All parameters NOT specially mentioned are measured at 24,48,96VDC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
File Name:SD-150-SPEC 2011-08-23