SD-15 Datasheet, PDF (1/2 Pages) Mean Well Enterprises Co., Ltd. – 15W Single Output DC-DC Converter

15W Single Output DC-DC Converter
SD-15 series
Features :
2:1 wide input range
Protections:Short circuit/Over load /voltage
Built-in EMI filter,low ripple noise
100% full load burn-in test
Low cost
High reliability
1 year warranty
SPECIFICATION
MODEL
OUTPUT
INPUT
PROTECTION
ENVIRONMENT
SAFETY &
EMC
OTHERS
SD-15A-05 SD-15B-05 SD-15C-05 SD-15A-12 SD-15B-12 SD-15C-12 SD-15A-24 SD-15B-24
DC VOLTAGE
5V
RATED CURRENT
3A
12V
1.25A
24V
0.625A
CURRENT RANGE
0 ~ 3A
0 ~ 1.25A
0 ~ 0.625A
RATED POWER
15W
15W
15W
RIPPLE & NOISE (max.) Note.2 100mVp-p
120mVp-p
150mVp-p
VOLTAGE ADJ.RANGE
4.75~5.5VDC
VOLTAGE TOLERANCE Note.3
2.0%
10.8~13.2VDC
1.0%
21.6~26.4VDC
1.0%
LINE REGULATION
0.5%
0.3%
0.2%
LOAD REGULATION
0.5%
0.3%
0.2%
SETUP, RISE ,HOLD UP TIME 2.5s, 25ms,--- 12VDC/24VDC/48VDC at full load
VOLTAGE RANGE
EFFICIENCY(Typ.)
A: 9.2 ~18VDC B:18 ~ 36VDC C:36~72VDC
68%
76%
75%
72%
76%
79%
70%
77%
DC CURRENT(Typ.)
OVER LOAD
1.9A/12VDC
0.9A/24VDC
0.45A/48VDC
105% -160% rated output power
Protection type : hiccup mode , recovers automatically after fault condition is removed
OVER VOLTAGE
WORKING TEMP.
5.75 ~ 6.75V
13.8~ 16.2V
¡ ^{Protection type : Shut down o/p voltage, re-power on to recover}
-10 60
27.6 ~ 32.4V
WORKING HUMIDITY
20 ~ 90% RH non-condensing
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
0.03%/ (0 ~ 50 )
10 ~ 500Hz, 2G 10min./1cycle, 60min.each along X, Y, Z axes
WITHSTAND VOLTAGE
I/P-O/P:2KVAC I/P-FG:1KVAC O/P-FG:0.5KVAC
ISOLATION RESISTANCE
I/P-O/P,I/P-FG,O/P-FG:100M Ohms/500VDC
EMI CONDUCTION&RADIATION Compliance to EN55022(CISPR22) CLASS B
EMS IMMUNITY
Compliance to EN61000-4-2,3,4,6,8;ENV50204,EN55024,light industry level,criteria A
DIMENSION
79*51*28mm (L*W*H)
PACKING
0.18kg,60 PCS/11.8kg
SD-15C-24
78%
NOTE
1. All parameters NOT specially mentioned are measured at normal input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
File Name:SD-15 SPEC.2006-04-19