SD-1000_10 Datasheet, PDF (1/4 Pages) Mean Well Enterprises Co., Ltd. – 1000W Single Output DC-DC Converter

1000W Single Output DC-DC Converter
SD-1000 series
Features :
1U low profile 41mm
High power density 10.7w/inch³
2000VAC I/O Isolation
Protections: Short circuit / Overload / Over voltage / Over temperature
Output OK signal
Built-in remote ON-OFF control
Built-in remote sense function
Forced air cooling by built-in DC fan with fan speed control
12V, 0.25A auxiliary output
3 years warranty
SPECIFICATION
MODEL
SD-1000L-12
SD-1000L-24
SD-1000L-48
SD-1000H-12
SD-1000H-24
SD-1000H-48
DC VOLTAGE
12V
24V
48V
12V
24V
48V
RATED CURRENT
60A
40A
21A
60A
40A
21A
CURRENT RANGE
0 ~ 60A
0 ~ 40A
0 ~ 21A
0 ~ 60A
0 ~ 40A
0 ~ 21A
RATED POWER
720W
960W
1008W
720W
960W
1008W
OUTPUT
RIPPLE & NOISE (max.) Note.2 150mVp-p
VOLTAGE ADJ. RANGE
11 ~ 15V
VOLTAGE TOLERANCE Note.3 1.0%
LINE REGULATION
0.5%
150mVp-p
23 ~ 30V
1.0%
0.5%
150mVp-p
46 ~ 60V
1.0%
0.5%
150mVp-p
11 ~ 15V
1.0%
0.5%
150mVp-p
23 ~ 30V
1.0%
0.5%
150mVp-p
46 ~ 60V
1.0%
0.5%
LOAD REGULATION
0.5%
0.5%
0.5%
0.5%
0.5%
0.5%
SETUP, RISE TIME
500ms, 50ms at full load
VOLTAGE RANGE Note.5 19 ~ 72VDC
72 ~ 144VDC
EFFICIENCY (Typ.)
84%
88%
90%
85%
89%
92%
INPUT
DC CURRENT (Typ.)
23.5A/48VDC
11.6A/96VDC
INRUSH CURRENT (Typ.) -----
100A/96VDC
OVERLOAD
105 ~ 125% rated output power
Protection type : Constant current limiting, unit will shut down o/p voltage after about 5sec. Re-power on to recover
PROTECTION OVER VOLTAGE
16 ~ 19V
30.8 ~ 35.2V
62 ~ 68V
16 ~ 19V
Protection type : Shut down o/p voltage, re-power on to recover
30.8 ~ 35.2V
62 ~ 68V
OVER TEMPERATURE
85 5 (TSW2 ) detect on heatsink of O/P diode; 75 5 (TSW1 ) detect on heatsink of power transistor
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
REMOTE ON/OFF CONTROL ^{Please refer to function manual}
FUNCTION
OUTPUT OK SIGNAL
Open collector signal low when PSU turns on, maximum, sink current :10mA
WORKING TEMP.
-20 ~ +60 (Refer to output load derating curve)
WORKING HUMIDITY
20 ~ 90% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +85 , 10 ~ 95% RH
TEMP. COEFFICIENT
0.02%/ (0 ~ 50 )
VIBRATION
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
SAFETY STANDARDS
IEC60950-1 CB approved by TUV
SAFETY & ^{WITHSTAND VOLTAGE}
I/P-O/P:2KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
EMC
ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH
(Note 4) _{EMI CONDUCTION & RADIATION} Compliance to EN55022 (CISPR22)
EMS IMMUNITY
Compliance to EN61000-4-2,3,4,6,8; ENV50204, light industry level, criteria A
MTBF
32K hrs min. MIL-HDBK-217F (25 )
OTHERS DIMENSION
295*127*41mm (L*W*H)
PACKING
1.94Kg; 6pcs/12.6Kg/0.99CUFT
NOTE
1. All parameters NOT specially mentioned are measured at 48, 96VDC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.”
(as available on http://www.meanwell.com)
5. Derating may be needed under low input voltages. Please check the derating curve for more details.
File Name:SD-1000-SPEC 2010-10-18