SCP-75_11 Datasheet, PDF (1/3 Pages) Mean Well Enterprises Co., Ltd. – 75W Single Output Switching Power Supply

75W Single Output Switching Power Supply
SCP-75 series
■ Features :
Universal AC input/Full range
Protections: Short circuit / Overload / Over voltage / Battery
polarity protections (by fuse)
Built-in temperature compensation function
Output voltage detection signal
Cooling by free air convection
LED indicator for power on
No load power consumption <0.75W
SPECIFICATION
MODEL
SCP-75-12
100% full load burn-in test
2 years warranty
SCP-75-24
DC VOLTAGE
13.8V
27.6V
RATED CURRENT
5.4A
2.7A
CURRENT RANGE
0 ~ 5.4A
0 ~ 2.7A
PEAK 5S
Note.6 6.5A
3.2A
OUTPUT
RATED POWER
74.5W
RIPPLE & NOISE (max.) Note.2 120mVp-p
VOLTAGE ADJ. RANGE
+15,-5%
VOLTAGE TOLERANCE Note.3 ± 2.0%
LINE REGULATION Note.4 ± 1.0%
LOAD REGULATION Note.5 ± 2.0%
SETUP, RISE TIME
500ms, 30ms/230VAC
1200ms, 30ms/115VAC at full load
74.5W
200mVp-p
+15,-5%
± 1.0%
± 1.0%
± 1.0%
HOLD UP TIME (Typ.)
50ms/230VAC 16ms/115VAC at full load
VOLTAGE RANGE
85 ~ 264VAC 120 ~ 370VDC
FREQUENCY RANGE
47 ~ 63Hz
INPUT
EFFICIENCY (Typ.)
81%
85%
AC CURRENT (Typ.)
1.5A/115VAC 0.9A/230VAC
INRUSH CURRENT (Typ.) COLD START 45A
LEAKAGE CURRENT
TEMP. COMPENSATION
FUNCTION
OUTPUT VOLTAGE SENSOR
OVERLOAD
PROTECTION
OVER VOLTAGE
<2mA / 240VAC
By NTC (not provide with the power supply)
L=output voltage +0.2 ~ 0.7V(AC OK); L=0V(AC Fail)
6.5 ~ 8.7A rated output power
3.2 ~ 4.3A rated output power
Protection type : Hiccup mode, recovers automatically after fault condition is removed
16.6 ~ 19.3V
33.1 ~ 38.6V
Protection type : Shut down o/p voltage, re-power on to recover
WORKING TEMP.
WORKING HUMIDITY
ENVIRONMENT STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
SAFETY STANDARDS
SAFETY & WITHSTAND VOLTAGE
-20 ~ +60℃ (Refer to output load derating curve)
20 ~ 90% RH non-condensing
-40 ~ +85℃, 10 ~ 95% RH
± 0.05% /℃ (0 ~ 45℃)
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
UL60950-1, CB(IEC60950-1),CCC GB4943 approved
I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
EMC
(Note 6)
ISOLATION RESISTANCE
EMC EMISSION
EMC IMMUNITY
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH
Compliance to EN55022 (CISPR22) Class B, EN61000-3-2,3
Compliance to EN61000-4-2, 3, 4, 5, 6, 8,11, ENV50204, EN55024, EN61000-6-1, light industry level, criteria A
OTHERS
MTBF
DIMENSION
PACKING
461.2K hrs min. MIL-HDBK-217F (25℃)
159*97*38mm (L*W*H)
0.5Kg; 30pcs/16Kg/1CUFT
NOTE
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Line regulation is measured from low line to high line at rated load.
5. Load regulation is measured from 0% to 100% rated load.
6. 33% Duty cycle maximum within every 15 seconds. Average output power should not exceed the rated power.
7. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
(As available on http://www.meanwell.com)
File Name:SCP-75-SPEC 2011-05-24