SBT01 Datasheet, PDF (1/1 Pages) Mean Well Enterprises Co., Ltd. – 1W DC-DC Unregulated Single Output Converter

1W DC-DC Unregulated Single Output Converter
SBT01 series
Features :
1000VDC I/O isolation
Internal SMD technology
Protection: Short circuit
Cooling by free air convection
Non-conductive plastic case
SMD package styles
100% full load burn-in test
Low cost / High reliability
Approved: UL / CUL
1 year warranty
SPECIFICATION
ORDER NO.
SBT01L-05 SBT01M-05 SBT01L-09 SBT01M-09 SBT01L-12 SBT01M-12
DC OUTPUT VOLTAGE
5V
9V
12V
OUTPUT CURRENT RANGE 0 ~ 200mA
0 ~ 111mA
0 ~ 84mA
EFFICIENCY
70%
72%
74%
75%
74%
75%
RATED POWER
1W
OUTPUT RIPPLE & NOISE (max.) Note.2 100mVp-p
LINE REGULATION Note.3 1.2% for 1% input variation
LOAD REGULATION Note.4 8.0%
VOLTAGE TOLERANCE
8.0%
SWITCHING FREQUENCY(Typ.) 100KHz
VOLTAGE RANGE
NORMAL VOLTAGE
4.5 ~ 5.5V
5V
10.8 ~ 13.2V 4.5 ~ 5.5V
12V
5V
10.8 ~ 13.2V 4.5 ~ 5.5V
12V
5V
10.8 ~ 13.2V
12V
INPUT
Full load 292mA
INPUT CURRENT
No load 29mA
120mA
15mA
292mA
29mA
120mA
15mA
292mA
29mA
120mA
15mA
PROTECTION
Fuse recommended
OVERLOAD
PROTECTION
SHORT CIRCUIT
Momentary
Protection type : Broken
Momentary
Protection type : Broken
WORKING TEMP.
-40 ~ +85 (Refer to output load derating curve)
WORKING HUMIDITY
20% ~ 90% RH non-condensing
ENVIRONMENT
SAFETY &
EMC
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
SAFETY STANDARDS
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
-40 ~ +105 , 10 ~ 95% RH
0.03% / (0 ~ 50 )
10 ~ 500Hz, 2G 10min./1 cycle, period for 60min. each along X, Y, Z axes
UL60950-1, CSA C22.2
I/P-O/P:1KVDC
I/P-O/P: 100M Ohms / 500VDC / 25 / 70% RH
MTBF
500khrs min. MIL-HDBK-217F(25 )
OTHERS DIMENSION
12.7*7.5*6.0mm or 0.50"*0.30"*0.24" inch (L*W*H)
WEIGHT
1.3g
SBT01L-15
15V
0 ~ 67mA
75%
4.5 ~ 5.5V
5V
292mA
29mA
SBT01M-15
75%
10.8 ~ 13.2V
12V
120mA
15mA
Mechanical Specification
Unit: mm (inch)
12.7
7.62
8765
TOP VIEW
1234
2.54
0.5
2.54
0.25
Pin Configuration
Pin No.
1
2
3
4
5
6
7
8
Output
-Vin
+Vin
NC
-Vout
+Vout
NC
NC
NC
Derating Curve
100
80
NOTE
-40
0
25 50 70 85 100
Ta ( )
1.All parameters are specified at normal input, rated load, 25 70% RH ambient.
2.Ripple & noise are measured at 20MHz by using a 12" twisted pair terminated with a 0.1uf & 47uf capacitor.
3.Line regulation is measured from low line to high line at rated load.
4.Load regulation is measured from 20% to 100% rated load.
File Name: SBT01-SPEC 2008-05-08