RSP-75 Datasheet, PDF (1/2 Pages) Mean Well Enterprises Co., Ltd. – 75W Single Output with PFC Function

75W Single Output with PFC Function
RSP-75 series
¡½ Features :
¡EUniversal AC input / Full range
¡EBuilt-in active PFC function
¡EProtections: Short circuit / Overload / Over voltage
¡ECooling by free air convection
¡EBuilt-in constant current limiting circuit
¡E1U low profile 30mm
¡ERemote ON-OFF control
¡ELED indicator for power on
¡E100% full load burn-in test
¡E3 years warranty
SPECIFICATION
Bauart gepruft
Sicherheit
egelma ge
od o s
be wac g
www.tuv.com
ID 2000000000
MODEL
RSP-75-3.3 RSP-75-5 RSP-75-7.5 RSP-75-12 RSP-75-13.5 RSP-75-15 RSP-75-24 RSP-75-27 RSP-75-48
DC VOLTAGE
3.3V
5V
7.5V
12V
13.5V
15V
24V
27V
48V
RATED CURRENT
15A
15A
10A
6.3A
5.6A
5A
3.2A
2.8A
1.6A
CURRENT RANGE
0 ~ 15A
0 ~ 15A
0 ~ 10A
0 ~ 6.3A 0 ~ 5.6A 0 ~ 5A
0 ~ 3.2A 0 ~ 2.8A 0 ~ 1.6A
RATED POWER
49.5W
75W
75W
75.6W
75.6W
75W
76.8W
75.6W
76.8W
OUTPUT
RIPPLE & NOISE (max.) Note.2 80mVp-p 80mVp-p
VOLTAGE ADJ. RANGE
3.14 ~ 3.63V 4.75 ~ 5.5V
VOLTAGE TOLERANCE Note.3 ¡Ó2.0%
¡Ó2.0%
LINE REGULATION
¡Ó0.5%
¡Ó0.5%
LOAD REGULATION
¡Ó1.0%
¡Ó1.0%
SETUP, RISE TIME
600ms, 30ms at full load
80mVp-p 80mVp-p 80mVp-p 80mVp-p 100mVp-p 100mVp-p 100mVp-p
7.13 ~ 8.25V 11.4 ~ 13.2V 12.8 ~ 14.9V 14.3 ~ 16.5V 22.8 ~ 26.4V 25.7 ~ 29.7V 45.6 ~ 52.8V
¡Ó2.0%
¡Ó2.0%
¡Ó2.0%
¡Ó2.0%
¡Ó1.0%
¡Ó1.0%
¡Ó1.0%
¡Ó0.5%
¡Ó0.5%
¡Ó0.5%
¡Ó0.5%
¡Ó0.5%
¡Ó0.5%
¡Ó0.5%
¡Ó1.0%
¡Ó0.5%
¡Ó0.5%
¡Ó0.5%
¡Ó0.5%
¡Ó0.5%
¡Ó0.5%
HOLD UP TIME (Typ.)
16ms at full load
VOLTAGE RANGE
85 ~ 264VAC 120 ~ 370VDC
FREQUENCY RANGE
47 ~ 63Hz
POWER FACTOR (Typ.)
PF>0.93/230VAC PF>0.98/115VAC at full load
INPUT EFFICIENCY (Typ.)
76%
80%
82%
83%
83%
85%
86%
86%
88%
AC CURRENT (Typ.)
INRUSH CURRENT (Typ.)
1.3A/115VAC 0.7A/230VAC
COLD START 30A/230VAC
LEAKAGE CURRENT
<2mA / 240VAC
OVERLOAD
PROTECTION OVER VOLTAGE
105 ~ 150% rated output power
Protection type : Constant current limiting, recovers automatically after fault condition is removed
3.63 ~ 4.46V 5.5 ~ 6.75V 8.25 ~ 10.13V 13.2 ~ 16.2V 14.85 ~ 18.23V 16.5 ~ 20.25V 26.4 ~ 32.4V 29.7 ~ 36.45V 52.8 ~ 64.8V
Protection type : Shut down o/p voltage, re-power on to recover
OVER TEMPERATURE
95¢J¡Ó5¢J (TSW1) detect on heatsink of power transistor
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
FUNCTION REMOTE CONTROL
CN1: < 0~0.8VDC POWER ON , 4~10VDC POWER OFF
WORKING TEMP.
-30 ~ +70¢J (Refer to "Derating Curve")
WORKING HUMIDITY
20 ~ 90% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -20 ~ +85¢J, 10 ~ 95% RH
TEMP. COEFFICIENT
¡Ó0.05%/¢J (0 ~ 50¢J)
VIBRATION
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
SAFETY STANDARDS
UL60950-1, TUV EN60950-1, CCC GB4943 approved; Design refer to EN60335-1
SAFETY & ^{WITHSTAND VOLTAGE}
EMC
ISOLATION RESISTANCE
(Note 4) EMC EMISSION
I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25¢J/ 70% RH
Compliance to EN55022 (CISPR22) Class B, EN61000-3-2,-3, GB9254 class B
EMC IMMUNITY
Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, light industry level, criteria A
MTBF
K hrs min. MIL-HDBK-217F (25¢J)
OTHERS DIMENSION
159*97*30mm (L*W*H)
NOTE
PACKING
Kg
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25¢J of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.”
(as available on http://www.meanwell.com)
File Name:RSP-75-SPEC 2012-10-09