PSD-15_11 Datasheet, PDF (1/2 Pages) Mean Well Enterprises Co., Ltd. – 15W DC-DC Single Output Switching Power Supply

15W DC-DC Single Output Switching Power Supply
PSD-15 series
Features :
Protections:Short circuit/Over load /Over voltage/Polarity
Cooling by free air convection
100% full load burn-in test
Low cost
High reliability
2 year warranty
SPECIFICATION
MODEL
PSD-15A-05 PSD-15B-05 PSD-15C-05 PSD-15A-12 PSD-15B-12 PSD-15C-12 PSD-15A-24 PSD-15B-24 PSD-15C-24
DC VOLTAGE
5V
RATED CURRENT
3A
12V
24V
1.25A
0.6A
CURRENT RANGE
0 ~ 3A
0 ~ 1.25A
0 ~ 0.6A
OUTPUT
RATED POWER
15W
RIPPLE & NOISE (max.) Note.2 50mVp-p
15W
100mVp-p
14.4W
100mVp-p
VOLTAGE TOLERANCE Note.3 2.0%
2.0%
2.0%
LINE REGULATION
1.0%
LOAD REGULATION
1.0%
1.0%
1.0%
0.5%
0.5%
SETUP, RISE, HOLD UP TIME 2.5s, 25ms, ----/12VDC/24VDC/48VDC at full load
INPUT
VOLTAGE RANGE
EFFICIENCY(Typ.)
A: 9.2 ~18VDC (12VDC) B:18 ~ 36VDC (24VDC) C:36~72VDC(48VDC)
74%
78%
78%
67%
78%
78%
72%
78%
79%
DC CURRENT(Typ.)
1.9A/12VDC 0.9A/24VDC 0.45A/48VDC
OVER LOAD
PROTECTION
105% -150% rated output power
Protection type : hiccup mode ,recovery automatically after fault condition is removed
OVER VOLTAGE
ENVIRONMENT
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
5.75 ~ 6.75V
13.8~ 16.2V
¡ ^{Protection type : Shut off o/p voltage, clamping by zener diode}
-10 60
20 ~ 90% RH non-condensing
20 ~ 95% RH non-condensing
27.6 ~ 32.4V
SAFETY &
EMC
TEMP. COEFFICIENT
VIBRATION
WITHSTAND VOLTAGE
10 ~ 500Hz, 2G 10min./1cycle, Period for 60min.each along X, Y, Z axes
I/P-O/P:2KVAC
ISOLATION RESISTANCE
I/P-O/P:100M Ohms/500VDC / 25 / 70% RH
EMI CONDUCTION&RADIATION Compliance to EN55022(CISPR22) CLASS B
EMS IMMUNITY
Compliance to EN61000-4-2, 3, 4, 6, 8 EN55024, EN61000-6-1 Light industry level, criteria A
OTHERS
MTBF
DIMENSION
PACKING
740.4Khrs min. MIL-HDBK-217F(25 )
94*49*25mm (L*W*H)
81mg;120pcs/10.72Kg
NOTE
1.All parameters NOT specially mentioned are measured at normal input,rated load and 25 of ambient temperature.
2.Ripple & noise are measued at 20 MHz of bandwidth by using a 12inch twisted pair-wire termined with a 0.1uf & 47uf capacitor.
3.Tolerance:includes set up tolerance,line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed
that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power
supplies.” (as available on http://www.meanwell.com)
File Name:PSD-15-SPEC 2011-03-09