PLN-20 Datasheet, PDF (1/3 Pages) Mean Well Enterprises Co., Ltd. – 20W Single Output LED Power Supply

20W Single Output LED Power Supply
PLN-20 series
Features :
Universal AC input / Full range(up to 277VAC)
Built-in constant current limiting circuit with adjustable OCP level
Fully isolated plastic case
Protections:Short circuit/Over load/Over voltage/Over temperature
Built-in active PFC function
IP64 design for indoor or outdoor installations
Small and compact size
Cooling by free air convection
100% full load burn-in test
High reliability,low cost
Suitable for Damp / wet locations
Suitable for LED lighting and moving sign applications
2 years warranty
SPECIFICATION
F ¹¹⁰ M M _{SELV IP64}
MODEL
PLN-20-12
PLN-20-18
PLN-20-24
PLN-20-36
DC VOLTAGE
12V
18V
24V
36V
LED OPERATION VOLTAGE Note.5 9 ~ 12V
RATED CURRENT
1.6A
CURRENT RANGE
0 ~ 1.6A
13.5 ~ 18V
1.1A
0 ~ 1.1A
18 ~ 24V
0.8A
0 ~ 0.8A
27 ~ 36V
0.55A
0 ~ 0.55A
OUTPUT
CURRENT ADJ. RANGE
75% ~ 100%
RATED POWER
19.2W
RIPPLE & NOISE (max.) Note.2 2.5Vp-p
VOLTAGE TOLERANCE Note.3 10%
19.8W
3.0Vp-p
19.2W
3.0Vp-p
19.8W
3.0Vp-p
LINE REGULATION
3.0%
LOAD REGULATION
10%
SETUP TIME
2300ms / 230VAC 3000ms / 115VAC at full load
VOLTAGE RANGE Note.4 90 ~ 277VAC 127~392VDC
FREQUENCY RANGE
47 ~ 63Hz
POWER FACTOR
PF 0.9 at 75~100% load, 115VAC/230VAC
INPUT EFFICIENCY(Typ.)
80%
81%
82%
83%
AC CURRENT
0.4A/115VAC 0.2A/230VAC
INRUSH CURRENT(max.) 40A/230VAC
LEAKAGE CURRENT
0.5mA / 240VAC
OVER CURRENT
95 ~ 110%
Note.5
Protection type : Constant current limiting, recovers automatically after fault condition is removed
SHORT CIRCUIT
PROTECTION
OVER VOLTAGE
Hiccup mode, recovers automatically after fault condition is removed.
14 ~ 16V
19 ~ 22V
27 ~ 34V
Protection type : Shut off o/p voltage, clamping by zener diode
41 ~ 46V
OVER TEMPERATURE
110 10 (TSW1)
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
WORKING TEMP.
WORKING HUMIDITY
-30 ~ +60 (Refer to output load derating curve)
20 ~ 90% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +80 , 10 ~ 95% RH
TEMP. COEFFICIENT
0.06%/ (0 ~ 50 )
VIBRATION
SAFETY STANDARDS
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
IEC61347-1, IEC61347-2-13, TUV EN61347-1, EN61347-2-13, UL8750, IP64 approved
SAFETY &
EMC
WITHSTAND VOLTAGE
I/P-O/P:3.75KVAC
ISOLATION RESISTANCE I/P-O/P:100M Ohms/500VDC / 25 / 70%RH
EMI CONDUCTION & RADIATION Compliance to EN55015
HARMONIC CURRENT
Compliance to EN61000-3-2 Class C( 75% load);EN61000-3-3
EMS IMMUNITY
Compliance to EN61000-4-2,3,4,5,6,8,11;EN61547, light industry level, criteria A
MTBF
643.6Khrs min. MIL-HDBK-217F (25 )
OTHERS DIMENSION
PACKING
148.5*38.5*28mm (L*W*H)
0.18Kg; 60pcs/12.8Kg/0.9CUFT
PLN-20-48
48V
36 ~ 48V
0.42A
0 ~ 0.42A
20.2W
3.8Vp-p
83.5%
54 ~ 60V
NOTE
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Derating may be needed under low input voltage, please check the static characteristic for more details.
5. Constant current operation region is within 75% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please
reconfirm special electrical requirements for some specific system design.
6. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
File Name:PLN-20-SPEC 2010-07-30