PB-1000 Datasheet, PDF (1/5 Pages) Mean Well Enterprises Co., Ltd. – 1000W Intelligent Single Output Battery Charger

1000W Intelligent Single Output Battery Charger
PB-1000 series
SPECIFICATION
Features :
Controlled by microprocessor
2/8 stage charging selectable on output panel
Universal AC input / Full range
Built-in active PFC function PF>0.95
Protection: Reverse Polarity / Short circuit / Over voltage / Over temperature
Charger for lead-acid batteries
3 color LED loading indicator
Built-in remote ON-OFF control
2-Bank charger
Temperature compensation function
FAN on/off control (depends on charging current)
3 years warranty
..
MODEL
PB-1000-12
PB-1000-24
PB-1000-48
BOOST CHARGE VOLTAGE 14.4V
28.8V
57.6V
FLOAT CHARGE VOLTAGE 13.8V
27.6V
55.2V
OUTPUT CURRENT
60A
34.7A
17.4A
RECOMMENDED BATTERY
OUTPUT
200 ~ 600Ah
CAPACITY(AMP HOURS)(Note 3)
120 ~ 350Ah
60 ~ 175Ah
BATTERY TYPE
Open & Sealed Lead Acid
LEAKAGE CURRENT FROM
<1mA
BATTERY (Typ.)
VOLTAGE RANGE
90 ~ 264VAC 127 ~ 370VDC
FREQUENCY RANGE
47 ~ 63Hz
EFFICIENCY (Typ.)
85%
88%
89%
INPUT
POWER FACTOR (Typ.)
0.95/230VAC 0.98/115VAC at full load
AC CURRENT (Typ.)
12A/115VAC 5.2A/230VAC
INRUSH CURRENT (Typ.) 25A/115VAC 50A/230VAC
LEAKAGE CURRENT
<3.5mA / 240VAC
OVER VOLTAGE
16 ~ 18V
32 ~ 35V
Protection type : Shut down o/p voltage, re-power on to recover
64.5 ~ 69.5V
PROTECTION
80 5 (12V), 85 5 (24V,48V) (TSW1: detect on heatsink of power transistor)
OVER TEMPERATURE
85 5 (12V),75 5 (24V,48V) (TSW2 : detect on heatsink of o/p diode)
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
SHORT CIRCUIT
YES, protected by internal circuit
REVERSE POLARITY
YES, protected by internal circuit
REMOTE CONTROL
Open: Normal work Short: Stop Charging
BATTER BANKS
2 banks (A & B)
FAST CHARGE
FUNCTION
CHARGER OK
2 / 8 stage selectable
Relay contact rating(max.): 30V/1A resistive ; "Short" when the unit is working properly, "Open"when the unit is failure or the protection function is activating
OUTPUT OK
Relay contact rating(max.): 30V/1A resistive ; "Short" when the battery is full, "Open" when the battery is still charging
TEMPERATURE COMPENSATION By NTC, compensate both banks at the same time
WORKING TEMP.
-20 ~ +60 (Refer to output load derating curve)
WORKING HUMIDITY
20 ~ 90% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +85 , 10 ~ 95% RH
TEMP. COEFFICIENT
0.05%/ (0 ~ 50 )
VIBRATION
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
SAFETY STANDARDS
UL60950-1, TUV EN60950-1 approved
SAFETY &
EMC
(Note 2)
WITHSTAND VOLTAGE
I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC 25 70%RH
EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22)
HARMONIC CURRENT
Compliance to EN61000-3-2,-3
EMS IMMUNITY
Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, light industry level, criteria A
MTBF
127.4Khrs min. MIL-HDBK-217F (25 )
OTHERS DIMENSION
300*184*70mm(L*W*H)
PACKING
3.5Kg; 4pcs/15Kg/1.83CUFT
NOTE
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
3. This is Mean Well's suggested range. Please consult your battery manufacturer for their suggestions about maximum charging current limitation.
File Name:PB-1000-SPEC 2008-05-12