NSD10-S_10 Datasheet, PDF (1/2 Pages) Mean Well Enterprises Co., Ltd. – 10W DC-DC Regulated Single Output

10W DC-DC Regulated Single Output
NSD10-S series
Features :
Wide 4:1 DC input range
Protections: Short circuit / Overload / Over voltage
1000VDC I/O isolation
Built-in EMI filter
Cooling by free air convection
Built-in remote ON-OFF control
100% full load burn-in test
Low cost
High reliability
2 years warranty
SPECIFICATION
MODEL
NSD10-12S3 NSD10-12S5 NSD10-12S9 NSD10-12S12 NSD10-12S15 NSD10-48S3 NSD10-48S5 NSD10-48S9 NSD10-48S12 NSD10-48S15
OUTPUT
DC VOLTAGE
3.3V
5V
RATED CURRENT
2.5A
2A
CURRENT RANGE
0.12 ~ 2.5A 0.1 ~ 2A
RATED POWER
8.25W
10W
CAPACITIVE LOAD (max.) 3300uF
RIPPLE & NOISE (max.) Note.2 75mVp-p
VOLTAGE TOLERANCE Note.3 2.0% max.
LINE REGULATION
1.0%
LOAD REGULATION
2.0%
1.0%
9V
12V
15V
3.3V
5V
1.1A
0.83A
0.67A
2.5A
2A
0.05 ~ 1.1A 0.04 ~ 0.83A 0.03 ~ 0.67A 0.12 ~ 2.5A 0.1 ~ 2A
9.9W
9.96W 10.05W 8.25W 10W
1.0%
1.0%
1.0%
2.0%
1.0%
9V
12V
15V
1.1A
0.83A
0.67A
0.05 ~ 1.1A 0.04 ~ 0.83A 0.03 ~ 0.67A
9.9W
9.96W 10.05W
1.0%
1.0%
1.0%
RATED DC INPUT
12VDC
48VDC
VOLTAGE RANGE
9.8 ~ 36VDC
22 ~ 72VDC
INPUT
EFFICIENCY (Typ.)
72%
75%
78%
79%
80%
74%
77%
78%
79%
80%
DC CURRENT
1.4A/12VDC
0.4A/48VDC
SHUTDOWN IDLE CURRENT 20mA/12VDC
OVERLOAD
PROTECTION
OVER VOLTAGE(CLAMP)
Above 105% rated output power
Protection type : Over power limiting, recovers automatically after fault condition is removed
3.8 ~ 4.95V 5.75 ~ 7.5V 10.4 ~ 13.5V 13.8 ~ 18V 17.3 ~ 22.5V 3.8 ~ 4.95V 5.75 ~ 7.5V 10.4 ~ 13.5V 13.8 ~ 18V 17.3 ~ 22.5V
SHORT CIRCUIT
Note.4 Recovers automatically after fault condition is removed
FUNCTION ON/OFF CONTROL
Logic "1" OPEN: ON logic "0" GND: OFF
WORKING TEMP.
-25 ~ +70
WORKING HUMIDITY
0% ~ 95% RH max.
ENVIRONMENT
STORAGE TEMP., HUMIDITY -40 ~ +85 , 0 ~ 95% RH
TEMP. COEFFICIENT
0.03%/ (0~60
SAFETY STANDARDS
UL60950-1 approved, Design refer to TUV EN60950-1
SAFETY & ISOLATION VOLTAGE
I/P-O/P:1KVDC
EMC
(Note 5)
ISOLATION RESISTANCE I/P-O/P:100M Ohms / 500VDC / 25 / 70% RH
EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B
EMS IMMUNITY
Compliance to EN61000-4-2,3,4,6,8; EN55024, light industry level, criteria A
MTBF
2138.2K hrs min. MIL-HDBK-217F (25 )
OTHERS DIMENSION
50.8*25.4*10mm (2"*1"*0.394") (L*W*H)
NOTE
PACKING
0.02Kg; 300pcs/7Kg/0.97CUFT
1. All parameters NOT specially mentioned are measured at 12, 48VDC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Short circuit not more than 60 seconds.
5. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.”
(as available on http://www.meanwell.com)
6. To insure proper operation, a 220uF/100V electrolytic capacitor with Esr <1 must be added to the input line.
7. EMC filter suggestion:
80uH
+
+
Vin
+
680uF
PSU
Vo
-
-
File Name:NSD10-S-SPEC 2010-10-18