NSD10-D_11 Datasheet, PDF (1/2 Pages) Mean Well Enterprises Co., Ltd. – 10W DC-DC Regulated Dual Output

10W DC-DC Regulated Dual Output
NSD10-D series
Features :
Wide 4:1 DC input range
Protections: Short circuit / Overload / Over voltage
1000VDC I/O isolation
Built-in EMI filter
Cooling by free air convection
Built-in remote ON-OFF control
100% full load burn-in test
Lost cost
High reliability
2 years warranty
SPECIFICATION
MODEL
NSD10-12D5
NSD10-12D12
NSD10-12D15
NSD10-48D5
NSD10-48D12
NSD10-48D15
OUTPUT
DC VOLTAGE
5V
-5V
12V
-12V 15V
-15V 5V
-5V
12V
-12V 15V
-15V
RATED CURRENT
1A
1A
0.42A 0.42A 0.33A 0.33A 1A
1A
0.42A 0.42A 0.33A 0.33A
CURRENT RANGE
0.05 ~ 1A 0.05 ~ 1A 0.02 ~ 0.42A 0.02 ~ 0.42A 0.016 ~ 0.33A 0.016 ~ 0.33A 0.05 ~ 1A 0.05 ~ 1A 0.02 ~ 0.42A 0.02 ~ 0.42A 0.016 ~ 0.33A 0.016 ~ 0.33A
RATED POWER
10W
10.08W
9.9W
10W
10.08W
9.9W
CAPACITIVE LOAD (max.) 1000uF
RIPPLE & NOISE (max.) Note.2 75mVp-p(10% ~ 100% load)
VOLTAGE TOLERANCE Note.3 4.0%
2.0%
2.0%
3.0%
2.0%
2.0%
LINE REGULATION
1.0%
LOAD REGULATION
3.0%
2.0%
1.0%
2.0%
2.0%
1.0%
RATED DC INPUT
12VDC
48VDC
VOLTAGE RANGE
9.8 ~ 36VDC
22 ~ 72VDC
INPUT
EFFICIENCY (Typ.)
76%
77%
77%
78%
77%
77%
DC CURRENT
1.4A/12VDC
0.4A/48VDC
SHUTDOWN IDLE CURRENT 20mA/12VDC
OVERLOAD
PROTECTION
OVER VOLTAGE(CLAMP)
Above 105% rated output power
Protection type : Over power limiting, recovers automatically after fault condition is removed
5.75 ~ 7.5V -5.75 ~ -7.5V 13.8 ~ 18V -13.8 ~ -18V 17.3 ~ 22.5V -17.3 ~ -22.5V 5.75 ~ 7.5V -5.75 ~ -7.5V 13.8 ~ 18V -13.8 ~ -18V 17.3 ~ 22.5V -17.3 ~ -22.5V
SHORT CIRCUIT
Note.4 Recovers automatically after fault condition is removed
FUNCTION ON/OFF CONTROL
Logic "1" OPEN: ON logic "0" GND: OFF
WORKING TEMP.
-25 ~ +70
WORKING HUMIDITY
0% ~ 95% RH max.
ENVIRONMENT
STORAGE TEMP., HUMIDITY -40 ~ +85 , 0 ~ 95% RH
TEMP. COEFFICIENT
0.03%/ (0~60 )
SAFETY STANDARDS
UL60950-1 approved, Design refer to TUV EN60950-1
SAFETY & ISOLATION VOLTAGE
I/P-O/P:1KVDC
EMC
(Note 5)
ISOLATION RESISTANCE
EMC EMISSION
I/P-O/P:100M Ohms / 500VDC / 25 / 70% RH
Compliance to EN55022 (CISPR22) Class B
EMC IMMUNITY
Compliance to EN61000-4-2,3,4,6,8; EN55024, light industry level, criteria A
MTBF
1878.5K hrs min. MIL-HDBK-217F (25 )
OTHERS DIMENSION
50.8*25.4*10mm (2"*1"*0.394") (L*W*H)
NOTE
PACKING
0.02Kg; 300pcs/7Kg/0.97CUFT
1. All parameters NOT specially mentioned are measured at 12, 48VDC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Short circuit not more than 60 seconds.
5. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.”
(as available on http://www.meanwell.com)
6. To insure proper operation, a 220uF/100V electrolytic capacitor with Esr <1 must be added to the input line.
7. EMC filter suggestion:
80uH
+
+
Vin
+
680uF
PSU
Vo
-
-
File Name:NSD10-D-SPEC 2011-08-17