MSP-100 Datasheet, PDF (1/2 Pages) Mean Well Enterprises Co., Ltd. – 100W Single Output Medical Type

100W Single Output Medical Type
MSP-100 series
SPECIFICATION
¡½ Features :
¡EUniversal AC input / Full range
¡EBuilt-in active PFC function
¡EHigh efficiency up to 90%
¡EWithstand 300VAC surge input for 5 seconds
¡EProtections: Short circuit / Overload / Over voltage
¡EProtections: Over temperature (optional)
¡ECooling by free air convection
¡E1U low profile 38mm
¡EMedical safety approved (MOOP level)
¡EBuilt-in remote ON-OFF control
¡ENo load power consumption<0.5W (Note.6)
¢J ¡EAll using 105 long life electrolytic capacitors
¡E5 years warranty
MODEL
MSP-100-3.3 MSP-100-5 MSP-100-7.5 MSP-100-12 MSP-100-15 MSP-100-24 MSP-100-36 MSP-100-48
OUTPUT
DC VOLTAGE
3.3V
5V
7.5V
12V
15V
RATED CURRENT
20A
17A
13.5A
8.5A
7A
CURRENT RANGE
0 ~ 20A
0 ~ 17A
0 ~ 13.5A
0 ~ 8.5A
0 ~ 7A
RATED POWER
66W
85W
101.3W
102W
105W
RIPPLE & NOISE (max.) Note.2 80mVp-p
80mVp-p
100mVp-p 120mVp-p 150mVp-p
VOLTAGE ADJ. RANGE
3.1 ~ 3.8V 4.75 ~ 5.8V 7.1 ~ 9V
11.4 ~ 13.8V 14.25 ~ 18V
VOLTAGE TOLERANCE Note.3 +2.5,-3.5% +2.5,-3.5% ¡Ó2.5%
¡Ó1.5%
¡Ó1.5%
LINE REGULATION
¡Ó0.5%
¡Ó0.5%
¡Ó0.5%
¡Ó0.3%
¡Ó0.3%
LOAD REGULATION
¡Ó2.0%
¡Ó2.0%
¡Ó1.5%
¡Ó0.8%
¡Ó0.8%
SETUP, RISE TIME
2500ms, 100ms/230VAC 2500ms, 100ms/115VAC at full load
HOLD UP TIME (Typ.)
50ms/230VAC 20ms/115VAC at full load
24V
4.5A
0 ~ 4.5A
108W
150mVp-p
22.8 ~ 28.8V
¡Ó1.5%
¡Ó0.2%
¡Ó0.5%
36V
2.9A
0 ~ 2.9A
104.4W
200mVp-p
34.2 ~ 39.6V
¡Ó1.5%
¡Ó0.2%
¡Ó0.5%
48V
2.2A
0 ~ 2.2A
105.6W
240mVp-p
45.6 ~ 55.2V
¡Ó1.5%
¡Ó0.2%
¡Ó0.5%
VOLTAGE RANGE Note.5 85 ~ 264VAC 120 ~ 370VDC
FREQUENCY RANGE
47 ~ 63Hz
POWER FACTOR (Typ.)
PF>0.95/230VAC PF>0.98/115VAC at full load
INPUT EFFICIENCY (Typ.)
78%
83%
84%
87.5%
88%
88.5%
89%
90%
AC CURRENT (Typ.)
1.2A/115VAC 0.6A/230VAC
INRUSH CURRENT (Typ.) 35A/115VAC 65A/230VAC
£g £g LEAKAGE CURRENT Note.7 Earth leakage current < 300 A/264VAC , Touch leakage current < 100 A/264VAC
OVERLOAD
105 ~ 135% rated output power
Protection type : Constant current limiting for Vo=50 ~ 100% of rated voltage, recovers automatically after fault condition is removed
PROTECTION OVER VOLTAGE
3.96 ~ 4.62V 6 ~ 7V
9.4 ~ 10.9V 14.4 ~ 16.8V 18.8 ~ 21.8V 30 ~ 34.8V
Protection type : Shut down o/p voltage, re-power on to recover
41.4 ~ 48.6V 57.6 ~ 67.2V
OVER TEMPERATURE
90¢J(3.3V ~ 7.5V) , 85¢J(12V ~ 48V) (TSW1 : detect on heatsink Q101 of power transistor)(optional)
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
FUNCTION REMOTE CONTROL
RC+/RC- : 0 ~ 0.8V= power on ; 4 ~ 10V = power off
WORKING TEMP.
-40 ~ +60¢J (Refer to "Derating Curve")
WORKING HUMIDITY
20 ~ 90% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +85¢J, 10 ~ 95% RH
TEMP. COEFFICIENT
¡Ó0.04%/¢J (0 ~ 50¢J)
VIBRATION
10 ~ 500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes
SAFETY STANDARDS
ANSI/AAMI ES60601-1, IEC60601-1 approved
SAFETY & ^{WITHSTAND VOLTAGE}
EMC
ISOLATION RESISTANCE
(Note 4) _{EMC EMISSION}
I/P-O/P:4KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25¢J/ 70% RH
Compliance to EN55011 (CISPR11) Class B, EN61000-3-2,-3
EMC IMMUNITY
Compliance to EN61000-4-2,3,4,5,6,8,11, EN60601-1-2
MTBF
295.7K hrs min. MIL-HDBK-217F (25¢J)
OTHERS DIMENSION
PACKING
159*97*38mm (L*W*H)
0.38Kg; 24pcs/10.1Kg/0.76CUFT
NOTE
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25¢J of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.”
(as available on http://www.meanwell.com)
5. Derating may be needed under low input voltages. Please check the derating curve for more details.
6. No load power consumption<0.5W when RC+ & RC- (CN100 pin1,2) 0 ~ 8V or short.
7. Touch current was measured from primary input to DC output.
8. When the input voltage is less than 40VAC, the SPS may exhibit degradation of performance. The final product manufacturers must re-confirm this
deviation that does not affect basic safety or essential performance.
File Name:MSP-100-SPEC 2012-08-24