IPC-300_1108 Datasheet, PDF (1/6 Pages) Mean Well Enterprises Co., Ltd. – 300W Industrial 1U ATX 12V/P4 PC Power Supply

300W Industrial 1U ATX 12V/P4 PC Power Supply
IPC-300A
SPECIFICATION
Features :
Meet 1U rack mount system
Universal AC input / Full range
Active power factor 94%
Protections:Short circuit / Overload / Over voltage
Forced air cooling by built-in DC fan
With power good and fail signal output
Built-in remote ON-OFF control
Remote DC sense +5V and +3.3V
With +5VSB:0 ~ 2.0A max.
100% full load burn-in test
High efficiency
2 years warranty
MODEL
IPC-300A
OUTPUT
OUTPUT NUMBER
CH1
CH2
CH3
CH4
CH5
STANDBY
DC VOLTAGE
3.3V
5V
12V
-5V
-12V
5VSB
RATED CURRENT
20A
30A
18A
0.5A
1A
2A
CURRENT RANGE
0 ~ 20A
1 ~ 30A
1 ~ 18A
0 ~ 0.5A
0.1 ~ 1A
0 ~ 2A
RATED POWER
300W continue. +5V,+3.3V,+12V combine total power output shall not exceed 270W.(The +5 & +3.3Volt combine total output shall not exceed 150W)
(The -5 & -12Volt combine total output shall not exceed 12W)
RIPPLE & NOISE (max.) Note.2 50mVp-p
50mVp-p
120mVp-p
100mVp-p
120mVp-p
50mVp-p
VOLTAGE ADJ. RANGE
CH2 : 5.05 ~ 5.5V
VOLTAGE TOLERANCE Note.3 5.0%
5.0%
7.0%
8.0%
10%
5.0%
LINE REGULATION
1.0%
1.0%
1.0%
2.0%
2.0%
1.0%
LOAD REGULATION
5.0%
5.0%
7.0%
8.0%
10%
5.0%
SETUP, RISE TIME
800ms, 20ms/230VAC 2500ms, 20ms/115VAC at full load
HOLD TIME (Typ.)
16ms/230VAC 16ms/115VAC at full load
INPUT
VOLTAGE RANGE
FREQUENCY RANGE
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT(max.)
OVER LOAD
PROTECTION OVER VOLTAGE
90 ~ 264VAC
47 ~ 63Hz
75%
4.6A/115VAC 2.3A/230VAC
40A/115VAC 80A/230VAC
3mA/240VAC
105 ~ 150% rated output power
Protection type : Shut down o/p voltage, re-power on to recover
+3.3V, +5V: 110% ~ 140% of rated voltage ; +12V:13.2V ~ 16V
Protection type : Shut down o/p voltage, re-power on to recover
SHORT CIRCUIT
All output equipped with short circuit
Protection type : Shut down o/p voltage, re-power on to recover
POWER GOOD SIGNAL
FUNCTION _{POWER FAIL SIGNAL}
The TTL compatible signal out with 100ms to 500ms delay after power set up
The TTL compatible signal will go down at least 1ms before +5V below 4.75V
PS-ON INPUT SIGNAL
Power off: PS-ON = "Hi" or ">2V" ; Power on: PS-ON = "Low" or "<0.5V"
WORKING TEMP.
-10 ~ +60 (Refer to "Derating Curve")
WORKING HUMIDITY
20 ~ 90% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +85 10 ~ 95% RH
TEMP. COEFFICIENT
0.05% / (0 ~ 50 )
VIBRATION
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
SAFETY STANDARDS
UL60950-1, TUV EN60950-1 approved
SAFETY & WITHSTAND VOLTAGE
I/P-O/P:1.5KVAC I/P-FG:1.5KVAC
EMC
(Note 4)
ISOLATION RESISTANCE
EMC EMISSION
I/P-O/P, I/P-FG, O/P-FG:50M Ohms / 500VDC / 25 / 70% RH
Compliance to EN55022 (CISPR22) Class B, Design refer to FCC part 15 Class B, EN61000-3-2,-3
EMC IMMUNITY
Compliance to EN61000-4-2,3,4, 5,6,8,11, light industry level, criteria A
MTBF
94.1K hrs min. MIL-HDBK-217F (25 )
OTHERS
CONNECTOR
COOLING
ATX main power connector * 1ea; +12V power connector * 1ea
Peripheral power connector * 3ea; Floppy drive power connector * 1ea
Forced air ventilation by 4cm DC fan
DIMENSION
260*83*40mm (L*W*H)
PACKING
1.46Kg; 10pcs/15.6Kg/0.89CUFT
NOTE
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Load regulation is measured from 20% to 100% max. Load.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.”
(as available on http://www.meanwell.com)
5. Derating may be needed under low input voltages. Please check the derating curve for more details.
File Name: IPC-300A-SPEC 2011-08-09