HSP-250_11 Datasheet, PDF (1/2 Pages) Mean Well Enterprises Co., Ltd. – 250W Single Output with PFC Function

250W Single Output with PFC Function
HSP-250 series
Features :
Universal AC input / Full range
Built-in active PFC function, PF>0.95
High efficiency up to 87%
Protections: Short circuit / Overload / Over voltage / Over temperature
Forced air cooling by built-in DC fan
1U low profile 41mm
Conformal coated
Built-in cooling fan ON-OFF control
Built-in remote sense function
3 years warranty
SPECIFICATION
MODEL
HSP-250-2.5
HSP-250-3.6
HSP-250-5
DC VOLTAGE
2.5V
3.6V
5V
RATED CURRENT
50A
50A
50A
CURRENT RANGE
0 ~ 50A
0 ~ 50A
0 ~ 50A
RATED POWER
125W
180W
250W
RIPPLE & NOISE (max.) Note.2 100mVp-p
100mVp-p
100mVp-p
OUTPUT
VOLTAGE ADJ. RANGE
2.3 ~ 2.8V
VOLTAGE TOLERANCE Note.3 2.0%
LINE REGULATION
0.5%
3.24 ~ 3.96V
2.0%
0.5%
4.5 ~ 5.5V
2.0%
0.5%
LOAD REGULATION
1.0%
1.0%
1.0%
SETUP, RISE TIME
3000ms, 50ms/230VAC 3000ms, 50ms/115VAC at full load
HOLD UP TIME (Typ.)
16ms/230VAC 16ms/115VAC at full load
VOLTAGE RANGE Note.5 85 ~ 264VAC 120 ~ 370VDC
FREQUENCY RANGE
47 ~ 63Hz
POWER FACTOR (Typ.)
PF>0.95/230VAC PF>0.98/115VAC at full load
INPUT EFFICIENCY (Typ.)
79%
83%
87%
AC CURRENT (Typ.)
INRUSH CURRENT (Typ.)
1.5A/115VAC 0.75A/230VAC
35A/115VAC 70A/230VAC
2A/115VAC 1A/230VAC
2.8A/115VAC 1.4A/230VAC
LEAKAGE CURRENT
<1.2mA / 240VAC
OVERLOAD
105 ~ 135% rated output power
Protection type : Hiccup mode, recovers automatically after fault condition is removed
PROTECTION OVER VOLTAGE
2.88 ~ 3.38V
4.14 ~ 4.86V
Protection type : Shut down o/p voltage, re-power on to recover
5.75 ~ 6.75V
OVER TEMPERATURE
80 5 (TSW2) detect on heatsink of power transistor ; 80 5 (TSW1) detect on heatsink of output transistor
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
FUNCTION FAN CONTROL
RTH3 60 10 Fan on ; RTH3 40 10 Fan off
WORKING TEMP.
-40 ~ +70 (Refer to "Derating Curve")
WORKING HUMIDITY
20 ~ 90% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +85 , 10 ~ 95% RH
TEMP. COEFFICIENT
0.03%/ (0 ~ 50 )
VIBRATION
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
SAFETY &
EMC
(Note 4)
SAFETY STANDARDS
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
EMC EMISSION
UL60950-1, TUV EN60950-1 approved
I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH
Compliance to EN55022 (CISPR22) Class B, EN61000-3-2,-3
EMC IMMUNITY
Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61000-6-2, heavy industry level, criteria A
MTBF
179.7K hrs min. MIL-HDBK-217F (25 )
OTHERS DIMENSION
199*105*41mm (L*W*H)
PACKING
0.97Kg;16pcs/16.5Kg/0.87CUFT
NOTE
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
5. Derating may be needed under low input voltages. Please check the derating curve for more details.
File Name:HSP-250-SPEC 2011-08-09