English
Language : 

MAX1020 Datasheet, PDF (8/47 Pages) Maxim Integrated Products – 10-Bit, Multichannel ADCs/DACs with FIFO, Temperature Sensing, and GPIO Ports
10-Bit, Multichannel ADCs/DACs with FIFO,
Temperature Sensing, and GPIO Ports
ELECTRICAL CHARACTERISTICS (continued)
(AVDD = DVDD = 2.7V to 3.6V (MAX1021/MAX1023/MAX1057), external reference VREF = 2.5V (MAX1021/MAX1023/MAX1057), AVDD =
DVDD = 4.75V to 5.25V (MAX1020/MAX1022/MAX1058), external reference VREF = 4.096V (MAX1020/MAX1022/MAX1058), fSCLK = 4.8MHz
(50% duty cycle), TA = -40°C to +85°C, unless otherwise noted. Typical values are at AVDD = DVDD = 3V (MAX1021/MAX1023/MAX1057),
AVDD = DVDD = 5V (MAX1020/MAX1022/MAX1058), TA = +25°C. Outputs are unloaded, unless otherwise noted.)
Note 1: Tested at DVDD = AVDD = +3.6V (MAX1021/MAX1023/MAX1057), DVDD = AVDD = +5.25V (MAX1020/MAX1022/MAX1058).
Note 2: Offset nulled.
Note 3: No bus activity during conversion. Conversion time is defined as the number of conversion clock cycles multiplied by the
clock period.
Note 4: See Table 5 for reference-mode details.
Note 5: Not production tested. Guaranteed by design.
Note 6: See the ADC/DAC References section.
Note 7: Fast automated test, excludes self-heating effects.
Note 8: Specified over the -40°C to +85°C temperature range.
Note 9: REFSEL[1:0] = 00 or when DACs are not powered up.
Note 10: DAC linearity, gain, and offset measurements are made between codes 115 and 3981.
Note 11: The DAC buffers are guaranteed by design to be stable with a 500pF load.
Note 12: Time required by the DAC output to power up and settle within 1 LSB in the external reference mode.
Note 13: All DAC dynamic specifications are valid for a load of 1nF and 10kΩ.
Note 14: Only one digital output (either DOUT, EOC, or the GPIOs) can be indefinitely shorted to either supply at one time.
Note 15: All digital inputs at either DVDD or DGND. DVDD should not exceed AVDD.
Note 16: See the Reset Register section and Table 9 for details on programming the SLOW bit.
Note 17: Clock mode 11 only.
Typical Operating Characteristics
(AVDD = DVDD = 3V (MAX1021/MAX1023/MAX1057), external VREF = 2.5V (MAX1021/MAX1023/MAX1057), AVDD = DVDD = 5V
(MAX1020/MAX1022/MAX1058), external VREF = 4.096V (MAX1020/MAX1022/MAX1058), fCLK = 4.8MHz (50% duty cycle), fSAMPLE
= 300ksps, CLOAD = 50pF, 0.1µF capacitor at REF, TA = +25°C, unless otherwise noted.)
SHUTDOWN CURRENT
vs. ANALOG SUPPLY VOLTAGE
0.30
SHUTDOWN CURRENT
vs. ANALOG SUPPLY VOLTAGE
0.20
SHUTDOWN CURRENT
vs. TEMPERATURE
0.6
0.25
0.18
0.5
0.20
0.15
0.10
0.05
MAX1020/MAX1022/MAX1058
0
4.75 4.85 4.95 5.05 5.15 5.25
SUPPLY VOLTAGE (V)
0.16
0.14
0.12
MAX1021/MAX1023/MAX1057
0.10
2.7
3.0
3.3
SUPPLY VOLTAGE (V)
0.4
0.3
0.2
0.1
0
3.6
-40 -15
10
35
60
85
TEMPERATURE (°C)
8 _______________________________________________________________________________________