DS34T101_08 Datasheet, PDF (8/16 Pages) Maxim Integrated Products – Single/Dual/Quad/Octal TDM-over-Packet Chip

ABRIDGED DATA SHEET
____________________________________________________ DS34T101, DS34T102, DS34T104, DS34T108
5 Features
Global Features
• TDMoP Interfaces
o DS34T101: 1 E1/T1 LIU/Framer/TDMoP interface
o DS34T102: 2 E1/T1 LIUs/Framers/TDMoP interfaces
o DS34T104: 4 E1/T1 LIUs/Framers/TDMoP interfaces
o DS34T108: 8 E1/T1 LIUs/Framers/TDMoP interfaces
o All four devices: optionally 1 high-speed E3/DS3/STS-1 TDMoP interface
o All four devices: each interface optionally configurable for serial operation for V.35 and RS530
• Ethernet Interface
o One 10/100 Mbps port configurable for MII, RMII or SSMII interface format
o Half or full duplex operation
o VLAN support according to 802.1p and 802.1Q including stacked tags
o Fully compatible with IEEE 802.3 standard
• End-to-end TDM synchronization through the IP/MPLS domain by on-chip, per-port TDM clock recovery
• 64 independent bundles/connections, each with its own:
o Transmit and receive queues
o Configurable jitter-buffer depth
o Connection-level redundancy, with traffic duplication option
• Flexible on-chip cross-connection capability
o Internal bundle cross-connect capability, with DS0 resolution
o Any framer receiver port to any TDMoP block receive interface to maintain bundle connectivity
o Any TDMoP block transmit interface to any framer transmit port to maintain bundle connectivity
• Packet loss compensation and handling of misordered packets
• Glueless SDRAM interface
• Complies with MPLS-Frame Relay Alliance Implementation Agreements 4.1, 5.1 and 8.0
• Complies with ITU-T standards Y.1413 and Y.1414.
• Complies with Metro Ethernet Forum 3 and 8
• Complies with IETF RFC 4553 (SAToP), RFC 5086 (CESoPSN) and RFC 5087 (TDMoIP)
• IEEE 1146.1 JTAG boundary scan
• 1.8V and 3.3V Operation with 5.0V tolerant I/O
Clock Synthesizers
• Clocks to operate LIUs, jitter attenuators, framers, BERTs and HDLC controllers can be synthesized from a
single clock input for both E1 and T1 operation (10MHz, 19.44MHz, 38.88MHz or 77.76MHz on the CLK_HIGH
pin or 1.544MHz or 2.048MHz on the MCLK pin)
• Clocks to operate the TDMoP clock recovery machines can synthesized from a single clock input (10MHz,
19.44MHz, 38.88MHz or 77.76MHz on the CLK_HIGH pin)
• Clock to operate TDMoP logic and SDRAM interface (50MHz or 75MHz) can be synthesized from a single
25MHz clock on the CLK_SYS pin
Line Interface Units (LIUs)
• Receives E1, T1 and G.703 2048kHz synchronization signal
• Fully software configurable including software-selectable internal Tx and Rx termination
• Suitable for both short-haul and long-haul applications
• Receive sensitivity options from (0dB to -12dB) to (0dB to -43dB) for E1 and to (0dB to -36dB) for T1
• Receive signal level indication: 0dB to -37.5dB
• Internal receive termination options for 75Ω, 100Ω, 110Ω, and 120Ω lines
• Receive monitor-mode gain settings of 14dB, 20dB, 26dB, and 32dB
• Flexible transmit waveform generation
Rev: 101708
8 of 16