DS75LV_0611 Datasheet, PDF (5/13 Pages) Maxim Integrated Products – Digital Thermometer and Thermostat

DS75LV: Digital Thermometer and Thermostat
OPERATION⎯MEASURING TEMPERATURE
The DS75LV measures temperature using a bandgap temperature sensing architecture. An on-board delta-sigma
analog-to-digital converter (ADC) converts the measured temperature to a digital value that is calibrated in degrees
centigrade; for Fahrenheit applications a lookup table or conversion routine must be used. The DS75LV is factory-
calibrated and requires no external components to measure temperature.
At power-up the DS75LV immediately begins converting temperature to a digital value. The resolution of the digital
output data is user-configurable to 9, 10, 11, or 12 bits, corresponding to temperature increments of 0.5°C, 0.25°C,
0.125°C, and 0.0625°C, respectively, with 9-bit default resolution at power-up. The resolution is controlled via the
R0 and R1 bits in the configuration register as explained in the CONFIGURATION REGISTER section of this data
sheet. Note that the conversion time doubles for each additional bit of resolution.
After each temperature measurement and analog-to-digital conversion, the DS75LV stores the temperature as a
16-bit two’s complement number in the 2-byte temperature register (see Figure 3). The sign bit (S) indicates if the
temperature is positive or negative: for positive numbers S = 0 and for negative numbers S = 1. The most recently
converted digital measurement can be read from the temperature register at any time. Since temperature
conversions are performed in the background, reading the temperature register does not affect the operation in
progress.
Bits 3 through 0 of the temperature register are hardwired to 0. When the DS75LV is configured for 12-bit
resolution, the 12 MSbs (bits 15 through 4) of the temperature register will contain temperature data. For 11-bit
resolution, the 11 MSbs (bits 15 through 5) of the temperature register will contain data, and bit 4 will read out as 0.
Likewise, for 10-bit resolution, the 10 MSbs (bits 15 through 6) will contain data, and for 9-bit the 9 MSbs (bits 15
through 7) will contain data, and all unused LSbs will contain 0s. Table 2 gives examples of 12-bit resolution digital
output data and the corresponding temperatures.
Figure 3. Temperature, T_OS, and T_HYST Register Format
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8
MS Byte
S
2⁶
2⁵
2⁴
2³
2²
2¹
2⁰
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
LS Byte
2^-1
2^-2
2^-3
2^-4
0
0
0
0
Table 2. 12-Bit Resolution Temperature/Data Relationship
TEMPERATURE (°C)
DIGITAL OUTPUT
(BINARY)
DIGITAL OUTPUT
(HEX)
+125
0111 1101 0000 0000
7D00h
+25.0625
0001 1001 0001 0000
1910h
+10.125
0000 1010 0010 0000
0A20h
+0.5
0000 0000 1000 0000
0080h
0
0000 0000 0000 0000
0000h
-0.5
1111 1111 1000 0000
FF80h
-10.125
1111 0101 1110 0000
F5E0h
-25.0625
1110 0110 1111 0000
E6F0h
-55
1100 1001 0000 0000
C900h
SHUTDOWN MODE
For power-sensitive applications, the DS75LV offers a low-power shutdown mode. The SD bit in the configuration
register controls shutdown mode. When SD is changed to 1, the conversion in progress will be completed and the
result stored in the temperature register after which the DS75LV will go into a low-power standby state. The O.S.
output will be cleared if the thermostat is operating in interrupt mode and O.S will remain unchanged in comparator
mode. The 2-wire interface remains operational in shutdown mode, and writing a 0 to the SD bit returns the
DS75LV to normal operation.
5 of 13