MAX4684_09 Datasheet, PDF (3/10 Pages) Maxim Integrated Products – 0.5Ω/0.8Ω Low-Voltage, Dual SPDT Analog Switches in UCSP

0.5Ω/0.8Ω Low-Voltage, Dual SPDT
Analog Switches in UCSP
ELECTRICAL CHARACTERISTICS—+3V SUPPLY (continued)
(V+ = +2.7V to +3.3V, V_IH = +1.4V, V_IL = +0.5V, T_A = T_MIN to T_MAX, unless otherwise noted. Typical values are at +3V and +25°C.)
(Notes 3, 9, 10)
PARAMETER
Turn-Off Time
Break-Before-Make
Delay
Charge Injection
Off-Isolation (Note 8)
Crosstalk
Total Harmonic
Distortion
NC_ Off-Capacitance
NO_ Off-Capacitance
NC_ On-Capacitance
NO_ On-Capacitance
DIGITAL I/O
Input Logic High
Input Logic Low
IN_ Input Leakage
Current
POWER SUPPLY
Power-Supply Range
Supply Current (Note 4)
SYMBOL
t_OFF
CONDITIONS
V+ = 2.7V, V_NO_ or V_NC_ = 1.5V;
R_L = 50Ω; C_L = 35pF; Figure 2
T_A
MIN
+25°C
E
t_BBM
Q
V+ = 2.7V, V_NO_, or V_NC_ = 1.5V;
R_L = 50Ω; C_L = 35pF; Figure 3
E
2
COM_ = 0; R_S = 0; C_L = 1nF; Figure 4 +25°C
V_ISO
C_L = 5pF; R_L = 50Ω; f = 100kHz;
V_COM_ = 1V_RMS; Figure 5
+25°C
V_CT
C_L = 5pF; R_L = 50Ω; f = 100kHz;
V_COM_ = 1V_RMS; Figure 5
+25°C
THD
R_L = 600Ω, IN_ = 2Vp-p, f = 20Hz to
20kHz
+25°C
C_{NC_(OFF)}
C_{NO_(OFF)}
C_{NC_(ON)}
C_{NO_(ON)}
f = 1MHz; Figure 6
f = 1MHz; Figure 6
f = 1MHz; Figure 6
f = 1MHz; Figure 6
+25°C
+25°C
+25°C
+25°C
V_IH
V_IL
I_IN_
V_IN_ = 0 or V+
E
1.4
E
E
-1
V+
I+
V+ = 5.5V; V_IN_ = 0 or V+
E
+25°C
E
1.8
-50
-200
TYP MAX UNITS
25
30
ns
40
15
ns
200
pC
-64
dB
-68
dB
0.03
%
84
pF
37
pF
190
pF
150
pF
V
0.5
V
1
µA
5.5
V
0.04
50
nA
200
Note 3: The algebraic convention used in this data sheet is where the most negative value is a minimum and the most positive
value a maximum.
Note 4: Guaranteed by design.
Note 5: ΔR_ON = R_ON(MAX) - R_ON(MIN), between NC1 and NC2 or between NO1 and NO2.
Note 6: Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the
specified analog signal ranges.
Note 7: Leakage parameters are 100% tested at T_A = +85°C, and guaranteed by correlation over rated temperature range.
Note 8: Off-isolation = 20log₁₀ (V_COM / V_NO), V_COM = output, V_NO = input to off switch.
Note 9: UCSP and TDFN parts are 100% tested at +25°C only and guaranteed by design and correlation at the full hot-rated
temperature.
Note 10: -40°C specifications are guaranteed by design.
_______________________________________________________________________________________ 3