MAX1645 Datasheet, PDF (3/32 Pages) Maxim Integrated Products – Advanced Chemistry-Independent, Level 2 Battery Chargers with Input Current Limiting

Advanced Chemistry-Independent, Level 2
Battery Chargers with Input Current Limiting
ELECTRICAL CHARACTERISTICS (continued)
(Circuit of Figure 1, V_DD = +3.3V, V_BATT = +16.8V, V_DCIN = +18V, T_A = 0°C to +85°C, unless otherwise noted. Typical values are at
T_A = +25°C.)
PARAMETER
SYMBOL
CONDITIONS
MIN TYP MAX UNITS
PDL Load Switch Threshold
Hysteresis
V_PDL-HYS V_CVS referred to V_BATT
100
200
300
mV
PDL Turn-Off Current
PDL Turn-On Resistance
CVS Input Bias Current
BATT Full-Charge Voltage
V_CSSN - V_PDL = 1V
PDL to GND
V_CVS = 28V
ChargingVoltage() = 0x41A0
ChargingVoltage() = 0x3130
V0
ChargingVoltage() = 0x20D0
ChargingVoltage() = 0x1060
6
12
mA
50
100
150
kΩ
6
20
µA
16.666 16.8 16.934
12.492 12.592 12.692
V
8.333 8.4 8.467
4.150 4.192 4.234
BATT Charge Current (Note 3)
I0
R_CS = 50mΩ
ChargingCurrent() =
0x0BC0
2.798 3.008 3.218
A
ChargingCurrent() =
0x0080
61.6
128 194.4 mA
DCIN Source Current Limit
(Note 3)
BATT Undervoltage Charge
Current
R_CSS = 40mΩ
MAX1645
MAX1645A
V_CLS = 4.096V
V_CLS = 2.048V
V_BATT = 1V,
R_CSI = 50mΩ
V_BATT = 1V,
R_CSI = 50mΩ
4.714 5.12 5.526
A
2.282 2.56 2.838
20
128
200
mA
61.6 128 194.4
BATT/CSIP/CSIN Input Voltage
Range
0
20
V
Total BATT Input Bias Current
Total of I_BATT, I_CSIP, and I_CSIN;
V_BATT = 0 to 20V
-700
700
µA
Total BATT Quiescent Current
Total of I_BATT, I_CSIP, and I_CSIN;
V_BATT = 0 to 20V, charge inhibited
-100
100
µA
Total BATT Standby Current
CSSP Input Bias Current
CSSN Input Bias Current
CSSP/CSSN Quiescent Current
Battery Voltage-Error Amp DC
Gain
Total of I_BATT, I_CSIP, and I_CSIN;
V_BATT = 0 to 20V, V_DCIN = 0
V_CSSP = V_CSSN = V_DCIN = 0 to 28V
V_CSSP = C_CSSN = V_DCIN = 0 to 28V
V_CSSP = V_CSSN = 28V, V_DCIN = 0
From BATT to CCV
-5
5
µA
-100 540 1000 µA
-100
35
100
mA
-1
1
µA
200
500
V/V
CLS Input Bias Current
Battery Voltage-Error Amp
Transconductance
V_CLS = V_REF/2 to V_REF
From BATT to CCV, ChargingVoltage() =
0x41A0, V_BATT = 16.8V
-1
0.111
0.05
0.222
1
µA
0.444 µA/mV
Battery Current-Error Amp
Transconductance
From CSIP/SCIN to CCI, ChargingCurrent() =
0x0BC0, V_CSIP - V_CSIN = 150.4mV
0.5
1
2 µA/mV
Input Current-Error Amp
Transconductance
From CSSP/CSSN to CCS, V_CLS = 2.048V,
V_CSSP - V_CSSN = 102.4mV
0.5
1
2 µA/mV
CCV/CCI/CCS Clamp Voltage
(Note 4)
V_CCV = V_CCI = V_CCS = 0.25V to 2V
150
300
600
mV
_______________________________________________________________________________________ 3