English
Language : 

MAX15006_1111 Datasheet, PDF (3/14 Pages) Maxim Integrated Products – 40V, Ultra-Low Quiescent-Current Linear Regulators in 6-Pin TDFN/8-Pin SO
◁
40V, Ultra-Low Quiescent-Current
Linear Regulators in 6-Pin TDFN/8-Pin SO
ELECTRICAL CHARACTERISTICS (continued)
(VIN = 14V, IOUT = 1mA, CIN = 0.1μF, COUT = 2.2μF, TA = TJ = -40°C to +125°C, unless otherwise noted. Typical specifications are at
TA = +25°C.) (Note 2)
PARAMETER
REGULATOR
Guaranteed Output Current
Output Voltage (Note 3)
Dropout Voltage (Notes 4, 5)
Line Regulation
Load Regulation
Output Current Limit
Output Voltage Noise
Power-Supply Rejection
Ratio
FB Threshold Voltage
FB Input Current
ENABLE LOGIC
Enable Threshold Voltage
Enable Threshold Hysteresis
Enable Pulldown Current
Enable to Regulation Time
THERMAL SHUTDOWN
Thermal Shutdown
Thermal Shutdown
Hysteresis
SYMBOL
CONDITIONS
IOUT
VOUT
VDO
VIN  VOUT + VDO
MAX15006A/MAX15007A
IOUT = 1mA
MAX15006B/MAX15007B
MAX15006C/MAX15007C
IOUT = 5mA, MAX15006B/MAX15007B
IOUT = 5mA, MAX15006C/MAX15007C
IOUT = 50mA, MAX15006B/MAX15007B
IOUT = 50mA, MAX15006C/MAX15007C
IOUT = 50mA, MAX15006A/MAX15007A
6V  VIN  35V, IOUT = 1mA
VIN = VOUT + 3V, IOUT = 100μA to 50mA
PSRR
VFB
IFB
100Hz to 100kHz, IOUT =
50mA, COUT = 2.2μF
VOUT = 3.3V
VOUT = 5V
f = 100Hz, VIN_RIPPLE = 500mVP-P, IOUT = 50mA
ILOAD = 1mA (MAX15006C/MAX15007C only)
VFB = 0V, 1.5V (MAX15006C/MAX15007C only)
VIL
VIH
Internally pulled down to GND
(Note 6)
TSHDN Junction temperature rising
THYST
MIN TYP MAX
50
3.25 3.3 3.35
4.925 5.0 5.075
1.8
10
30
53
30
60
300 525
300 600
1000
0.25
0.7 1.5
80
350
115
179
66
1.2
-100
1.23 1.26
+100
0.4
1.4
60
0.5
0.4
2
+165
20
UNITS
mA
V
mV
%
%
mA
μVRMS
dB
V
nA
V
mV
μA
ms
°C
°C
Note 2: Limits at TA = -40°C are guaranteed by design.
Note 3: Output voltage regulation is guaranteed for IOUT ≥ 5μA.
Note 4: Dropout voltage is defined as (VIN - VOUT) when VOUT is 2% below the value of VOUT when VIN = VOUT + 3V.
Note 5: For VOUT = 3.3V, the 700mV dropout indicates VOUT does not reach 2% below VOUT at VIN = VOUT + 3V at minimum 4V
input voltage.
Note 6: Enable to regulation time is the time the output takes to reach 95% of its final value with VIN = 14V and EN is taken from VIL
to VIH in 5ns.
_______________________________________________________________________________________ 3
 ▷