MAX14895E Datasheet, PDF (3/11 Pages) Maxim Integrated Products – Enhanced VGA Port Protector DDC Outputs have Internal Pullups

MAX14895E
Enhanced VGA Port Protector
ELECTRICAL CHARACTERISTICS* (continued)
(V_CC = +4.75V to +5.25V, T_A = -40NC to +85NC, unless otherwise noted. Typical values are at V_CC = +5V, T_A = +25NC.) (Note 2)
PARAMETER
SYNCH0, SYNCV0 Leakage
Current
EN, EN Input Resistance
SYNCH1, SYNCV1
Output Logic-High
Output Logic-Low
Rising Time
SYMBOL
CONDITIONS
SYNCH0/SYNCV0 = GND or V_CC
EN = V_CC, EN = GND
MIN TYP MAX UNITS
-1
+1
FA
200
800
kI
V_OH V_CC = +4.75V, source 10mA
2.4
V_OL
V_CC = +4.75V, sink 10mA
t_R
R_L = 2.2kI, C_L = 10pF, 10% to 90% of V_CC
(Note 3)
V
0.5
V
4
ns
Falling Time
t_F
R_L = 2.2kI, C_L = 10pF, 90% to 10% of V_CC
(Note 3)
4
ns
Propagation Delay
t_PD
R_L = 2.2kI, C_L = 10pF, EN = V_CC, EN =
GND (Figure 1)
16
ns
Enable Time
t_EN
R_L = 2.2kI, C_L = 10pF, V_SYNCH1, V_SYNCV1
= +4.75V (Figure 1)
17
Fs
SDA_, SCL_ (DDC)
On-Resistance
R_ON
V_SDA0 = V_SCL0 = 0.5V, I_LOAD = 10mA
55
I
SDA0, SCL0 Off-Leakage Current
EN = GND, EN = V_CC,
-1
SDA0 = SCL0 = V_CC, SDA1 = SCL1 = GND
+1
FA
SDA1, SCL1 Reverse-Leakage
Current
V_CC = 0V, V_S = +5.25V,
V_SDA1 = V_SCL1 = +5.25V
-10
+10
FA
SDA1, SCL1 Pullup Resistor
R_PULLUP
V_CC = +4.75V, SDA0 = SCL0 =
unconnected, EN = V_CC , EN = GND,
I_LOAD = 100FA
1.25 2.5
4.0
kI
V_S OUTPUT
Forward Voltage Drop
I_LOAD = 60mA, V_CC = 5V
0.25
V
Reverse-Leakage Current
V_CC = 0V, V_S = 5.25V
10
FA
Current Limit
I_LIM
200
600
mA
Discharge Resistor
R_VS
I_LOAD = 1mA
300 500
I
THERMAL SHUTDOWN
Thermal Shutdown Threshold
+150
NC
Thermal Shutdown Hysteresis
10
NC
ESD PROTECTION
SDA1, SCL1, SYNCH1, SYNCV1,
RED, GRN, BLU, EN, V_S
HBM
IEC 61000-4-2 Contact
±15
kV
±8
kV
Note 2: All devices are 100% production tested at T_A = +25NC. Limits over the operating temperature range are guaranteed by
design and not production tested.
Note 3: Guaranteed by design.
����������������������������������������������������������������� Maxim Integrated Products   3
*The parametric values (min, typ, max limits) shown in the Electrical Characteristics table supersede values quoted elsewhere in this data sheet.