 English |
|
|
|
|
|
|
|
| DG-403-DJ Datasheet, PDF (3/8 Pages) Maxim Integrated Products – Improved, Dual, High-Speed Analog Switches | |||
| |||
| ◁ |
Improved, Dual, High-Speed Analog Switches
ELECTRICAL CHARACTERISTICS (continued)
(V+ = 15V, V- = -15V, VL = +5V, GND = 0V, VINH = +2.4V, VINL = +0.8V, TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
INPUT
Input Current with Input Voltage High IINH VIN = 2.4V, all others = 0.8V
Input Current with Input Voltage Low IINL VIN = 0.8V, all others = 2.4V
SUPPLY
Power-Supply Range
Positive Supply Current
All channels on or off, TA = +25°C
I+
V+ = 16.5V, V- = -16.5V,
VIN = 0V or 5V
TA = TMIN to TMAX
MIN
TYP MAX
(Note 2)
UNITS
-1.0 0.005 1.0 µA
-1.0 0.005 1.0 µA
±4.5
±20 V
-1.0 0.01 1.0
µA
-5.0
5.0
Negative Supply Current
All channels on or off, TA = +25°C
I-
V+ = 16.5V, V- = -16.5V,
VIN = 0V or 5V
TA = TMIN to TMAX
-1.0 0.01 1.0
µA
-5.0
5.0
Logic Supply Current
All channels on or off, TA = +25°C
IL
V+ = 16.5V, V- = -16.5V,
VIN = 0V or 5V
TA = TMIN to TMAX
-1.0 0.01 1.0
µA
-5.0
5.0
Ground Current
DYNAMIC
Turn-On Time
Turn-Off Time
Break-Before-Make Delay (Note 3)
IGND
tON
tOFF
tD
All channels on or off, TA = +25°C
V+ = 16.5V, V- = -16.5V,
VIN = 0V or 5V
TA = TMIN to TMAX
Figure 2
Figure 2
DG403 only,
Figure 3
TA = +25°C
TA = +25°C
TA = +25°C
-1.0 0.01 1.0
µA
-5.0
5.0
100 150 ns
60 100 ns
10
20
ns
Charge Injection (Note 3)
Off Isolation (Note 5)
Q
OIRR
CL = 1.0nF, VGEN = 0V,
RGEN = 0â¦, Figure 4
TA = +25°C
RL = 100â¦, CL = 5pF,
f = 1MHz, Figure 5
TA = +25°C
10 15 pC
72
dB
Crosstalk (Note 6)
Source-Off Capacitance
Drain-Off Capacitance
Channel-On Capacitance
RL = 50â¦, CL = 5pF,
f = 1MHz, Figure 6
CS(OFF) f = 1MHz, Figure 7
CD(OFF) f = 1MHz, Figure 7
CD(ON)
or CS(ON)
f = 1MHz, Figure 8
TA = +25°C
TA = +25°C
TA = +25°C
TA = +25°C
90
dB
12
pF
12
pF
39
pF
Note 2: This data sheet uses the algebraic convention, where the most negative value is a minimum and the most positive value is a
maximum.
Note 3: Guaranteed by design.
Note 4: ârON = ârON(max) - ârON(min). On-resistance match between channels and flatness are guaranteed only with specified
voltages. Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured at the
extremes of the specified analog signal range.
Note 5: Off isolation = 20log (VS/VD), VD = output, VS = input to off switch.
Note 6: Between any two switches.
Note 7: Leakage parameters IS(OFF), ID(OFF), and ID(ON) are 100% tested at the maximum rated hot temperature and guaranteed by
correlation at +25°C.
_______________________________________________________________________________________ 3
|
▷ |
German
Russian
Spanish
Italian
Polish
Chinese
Japanese
Korean
French
Portuguese