 English |
|
|
|
|
|
|
|
| MAX6381_07 Datasheet, PDF (2/13 Pages) Maxim Integrated Products – SC70/μDFN, Single/Dual Low-Voltage, Low-Power μP Reset Circuits | |||
| |||
| ◁ |
SC70/µDFN, Single/Dual Low-Voltage,
Low-Power µP Reset Circuits
ABSOLUTE MAXIMUM RATINGS
VCC to GND ..........................................................-0.3V to +6.0V
RESET Open-Drain Output....................................-0.3V to +6.0V
RESET, RESET (push-pull output) ..............-0.3V to (VCC + 0.3V)
MR, RESET IN.............................................-0.3V to (VCC + 0.3V)
Input Current (VCC) .............................................................20mA
Output Current (all pins) .....................................................20mA
Continuous Power Dissipation (TA = +70°C)
3-Pin SC70 (derate 2.9mW/°C above +70°C) ..............235mW
4-Pin SC70 (derate 3.1mW/°C above +70°C) ..............245mW
6-Pin µDFN (derate 2.1mW/°C above +70°C) ..........167.7mW
Operating Temperature Range .........................-40°C to +125°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under âAbsolute Maximum Ratingsâ may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VCC = full range, TA = -40°C to +125°C, unless otherwise specified. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
Operating Voltage Range
VCC Supply Current
VCC Reset Threshold
(See Reset Thresholds table)
Reset Threshold Tempco
VCC to Reset Delay
Reset Timeout Period
MAX6381âMAX6389
(See Reset Timeout table)
Reset Timeout Period
MAX6390
SYMBOL
CONDITIONS
VCC
VCC = 5.5V, no load
ICC
VCC = 3.6V, no load
VCC = 2.5V, no load
VCC = 1.8V, no load
TA = +25°C
VTH
TA = -40°C to +125°C
âVTH/°C
tRP
tRP
VCC falling at 10mV/µs from VTH + 100mV
to VTH - 100mV
D1
D2
D3
D5
D6
D4
D7
MR timeout period
D4
D7
D4
VCC timeout period
D7
MIN
1.0
VTH -
1.5%
VTH -
2.5%
1
20
140
280
560
1120
1200
140
150
1120
1200
TYP
7
6
4
3
VTH
VTH
60
35
MR Input Voltage
VIL
VTH < 4V
VIH
VIL
VTH > 4V
VIH
0.7 x
VCC
2.4
MAX UNITS
5.5
V
13
11
µA
7
6
VTH +
1.5%
V
VTH +
2.5%
ppm/°C
µs
2
40
280
560
ms
1120
2240
2400
280
300
ms
2240
2400
0.3 x
VCC
V
0.8
2 _______________________________________________________________________________________
|
▷ |
German
Russian
Spanish
Italian
Polish
Chinese
Japanese
Korean
French
Portuguese