MAX4929E Datasheet, PDF (2/13 Pages) Maxim Integrated Products – HDMI 2:1 Low-Frequency Translating Switch

HDMI 2:1 Low-Frequency Translating Switch
ABSOLUTE MAXIMUM RATINGS
(All voltages referenced to GND, unless otherwise noted.)
V+ ............................................................................-0.3V to +6V
All Pins (except GND) .............................................-0.3V to +6V
Continuous Current into Any I/O Terminal .........................25mA
Continuous Power Dissipation (T_A = +70°C)
20-Pin QSOP (derate 9.1mW/°C above +70°C) ..........727mW
20-Pin TQFN (derate 16.9mW/°C above +70°C) ......1356mW
Operating Temperature Range ...........................-40°C to +85°C
Storage Temperature Range .............................-65°C to +150°C
Junction Temperature ......................................................+150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V+ = +5V ±10%, CLP = VL = +3.3V ±10%, T_A = T_MIN to T_MAX, unless otherwise noted. Typical values are at T_A = +25°C.)
PARAMETER
POWER SUPPLY
V+ Supply Current
V+ Supply Current
VL Supply Current
CLP Supply Current
ANALOG SWITCH
SYMBOL
CONDITIONS
I+
V+ = 5.5V, VL = CLP = 3.6V
I+
V+ = 0V, VL = CLP = 0V, V_{HPIR_} = +5.5V
I_VL
V+ = 5.5V, VL = CLP = 3.6V
I_CLP
V+ = 5.5V, VL = CLP = 3.6V
MIN TYP MAX UNITS
3
8
µA
200
µA
1
µA
1
µA
On-Resistance
R_{ON(SCL_),} V+ = 4.5V, CLP = 3V, V_{SCL_} or V_{SDA_} = 0 to
R_{ON(SDA_)} 1.5V; I_{SCL_} or I_{SDA_} = ±10mA
10
25
Ω
On-Resistance Match Between
Channels
ΔR_ON
V+ = 4.5V, CLP = 3V, V_{SCL_} or V_{SDA_} = 0 to
1.5V; I_{SCL_} or I_{SDA_} = ±10mA
2
8
Ω
On-Resistance Flatness
R_FLAT
V+ = 4.5V, CLP = 3V, V_{SCL_} or V_{SDA_} = 0 to
1.5V; I_{SCL_} or I_{SDA_} = ±10mA
13
Ω
Off-Leakage Current
I_{SCL_(OFF),} V+ = 5.5V, V_{SCL_} or V_{SDA_} = 0V, 5.5V;
-5
I_{SDA_(OFF)} HIZ1 = HIZ2 = 0V or VL (Note 1)
+5
µA
On-Leakage Current
I_{SCL_(ON),} V+ = 5.5V, V_{SCL_} or V_{SDA_} = 0V, 5.5V
I_{SDA_(ON)} (Note 1)
-5
+5
µA
Output Clamped Voltage
V_OVC(SCLO), V+ = 5V, CLP = 3.3V, VL = 5V, R_P = 1kΩ
V_OVC(SDAO) (Note 2)
SWITCH DYNAMIC CHARACTERISTICS
3.3
V
SCL_, SDA_ Off-Capacitance
C_{SCL_(OFF),}
C_{SDA_(OFF)}
V+ = 5V, T_A = +25°C, Figure 1
20
pF
SCL_, SDA_ On-Capacitance
C_{SCL_(ON),}
C_{SDA_(ON)}
V+ = 5V, T_A = +25°C, Figure 1
30
pF
Bandwidth
Crosstalk
BW
R_S = R_L = 50Ω, C_L = 10pF
40
V_CT
R_S = R_L = 50Ω, f = 1MHz, Figure 2 (Note 3)
-75
MHz
dB
Off-Isolation
V_ISO
R_S = R_L = 50Ω, f = 1MHz, Figure 2 (Note 4)
-70
dB
LOGIC INPUT (HPIR1, HPIR2)
Input Logic-Low Voltage
Input Logic-High Voltage
V_IL
V+ = 4.5V
V_IH
V+ = 5.5V
0.8
V
3.8
V
Input Logic Leakage
I_INL
0.01
1
µA
2 _______________________________________________________________________________________