MAX4885 Datasheet, PDF (2/13 Pages) Maxim Integrated Products – Complete VGA 1:2 or 2:1 Multiplexer

Complete VGA 1:2 or 2:1 Multiplexer
ABSOLUTE MAXIMUM RATINGS
(All voltages referenced to GND.)
V₊, V_CL .....................................................................-0.3V to +6V
R_, G_, B_, DDCA_, DDCB_, SEL, M,
EN, QP (Note 1) ...........................................-0.3V to V+ + 0.3V
H_, V_ .......................................................................-0.3V to +6V
Continuous Current Through RGB Switches ....................±70mA
Continuous Current Through HV, DDC Switches…..........±50mA
Peak Current Through RGB Switches
(pulsed at 1ms, 10% duty cycle).................................±140mA
Peak Current Through HV, DDC Switches (pulsed at 1ms,
10% duty cycle)..............................................................±100mA
Continuous Power Dissipation (T_A = +70°C)
32-Pin TQFN (derate 21.3mW/°C above +70°C) ........1702mW
Operating Temperature Range ...........................-40°C to +85°C
Storage Temperature Range .............................-65°C to +150°C
Junction Temperature ......................................................+150°C
Lead Temperature (soldering, 10s) .................................+300°C
Note 1: Signals exceeding V+ or GND are clamped by internal diodes. Limit forward-diode current to maximum current rating.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V+ = +5.0V ±10%, V_CL = +3.3V ±10%, T_A = T_MIN to T_MAX, QP = GND, unless otherwise noted. Typical values are at V+ = +5.0V,
V_CL = +3.3V and T_A = +25°C.)
PARAMETER
SYMBOL
CONDITIONS
MIN TYP MAX UNITS
Supply Voltage Range
V+
4.5
5.5
V
Clamp Voltage Range
V₊ Quiescent Supply Current
V_CL
I₊
V+ = +5.5V
QP = GND
QP = V+
2.7
V+
V
0.3
0.5
mA
1
µA
V_CL Quiescent Supply Current
V₊ Shutdown Current
I_CL
I_+SHDN
V_CL = V+ = +5.5V
V+ = +5.5V, all digital inputs to V+ or GND
1
µA
5
µA
V_CL Shutdown Current
I_CLSHDN
V_CL = V+ = +5.5V, all digital inputs to V+ or
GND
1
µA
RGB ANALOG SWITCHES
On-Resistance
On-Resistance Matching
On-Resistance Flatness
Off-Leakage Current
On-Leakage Current
Charge Injection
R_ON
∆R_ON
R_FLAT(ON)
I_L(OFF)
I_L(ON)
Q
0V < V_IN < +2.5V, ^{QP = GND}
I_IN = -40mA
QP = V+
0V < V_IN < +2.5V, I_IN = -40mA
0V < V_IN < +2.5V, I_IN = -40mA
R_, G_, B_ = 0V or +5.5V, EN = GND
R_, G_, B_ = 0V or +5.5V, EN = V+
R_, G_, B_ = 0V,
C_L = 1000pF
QP = GND
QP = V+
5
7.5
Ω
6
10
0.5
1.5
Ω
0.02 0.75
Ω
-1
+1
µA
-1
+1
µA
10
pC
8
HV MULTIPLEXER
Input-Voltage Low
Input-Voltage High
High-Output Drive Current
Low-Output Drive Current
On-Resistance
Charge Injection
V_ILHV
V_IHHV
I_OHHV
I_OLHV
R_ONHV
Q
M = GND
M = GND
V_OUT = V₊ - 0.5V, M = GND
V_OUT = +0.5V, M = GND
H_ = V_ = +2.5V, I_IN = -40mA, M = V+
H_, V_ = 0V, M = V+, C_L = 1000pF
0.8
V
2.0
V
-16
mA
+16
mA
15
Ω
21
pC
2 _______________________________________________________________________________________