MAX410_08 Datasheet, PDF (2/16 Pages) Maxim Integrated Products – Single/Dual/Quad, 28MHz, Low-Noise, Low-Voltage, Precision Op Amps

Single/Dual/Quad, 28MHz, Low-Noise,
Low-Voltage, Precision Op Amps
ABSOLUTE MAXIMUM RATINGS
Supply Voltage .......................................................................12V
Differential Input Current (Note 1) ....................................±20mA
Input Voltage Range........................................................V+ to V-
Common-Mode Input Voltage ..............(V+ + 0.3V) to (V- - 0.3V)
Short-Circuit Current Duration....................................Continuous
Continuous Power Dissipation (T_A = +70°C)
MAX410/MAX412
8-Pin Plastic DIP (derate 9.09mW/°C above +70°C) ...727mW
8-Pin SO (derate 5.88mW/°C above +70°C)................471mW
8-Pin TDFN (derate 24.4mW/°C above +70°C) .........1951mW
MAX414
14-Pin Plastic DIP (derate 10.00mW/°C above +70°C)800mW
14-Pin SO (derate 8.33mW/°C above +70°C)..............667mW
Operating Temperature Ranges:
MAX41_C_ _ .......................................................0°C to +70°C
MAX41_E_ _.....................................................-40°C to +85°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Note 1: The amplifier inputs are connected by internal back-to-back clamp diodes. In order to minimize noise in the input stage, current-
limiting resistors are not used. If differential input voltages exceeding ±1.0V are applied, limit input current to 20mA.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V+ = 5V, V- = -5V, T_A = +25°C, unless otherwise noted.)
PARAMETER
Input Offset Voltage
Input Bias Current
Input Offset Current
Differential Input Resistance
Common-Mode Input Resistance
Input Capacitance
Input Noise-Voltage Density
SYMBOL
V_OS
I_B
I_OS
R_IN(Diff)
R_IN(CM)
C_IN
e_n
CONDITIONS
MAX410, MAX410B, MAX412, MAX412B
MAX414, MAX414B
MAX410, MAX412,
MAX414
10Hz
1000Hz (Note 2)
MAX410B, MAX412B,
MAX414B
1000Hz (Note 2)
Input Noise-Current Density
i_n
f_O = 10Hz
f_O = 1000Hz
Common-Mode Input Voltage
V_CM
Common-Mode Rejection Ratio
Power-Supply Rejection Ratio
Large-Signal Gain
CMRR
PSRR
A_VOL
V_CM = ±3.5V
V_S = ±2.4V to ±5.25V
R_L = 2kΩ, V_O = ±3.6V
R_L = 600Ω, V_O = ±3.5V
Output Voltage Swing
V_OUT R_L = 2kΩ
Short-Circuit Output Current
Slew Rate
Unity-Gain Bandwidth
Settling Time
Channel Separation
I_SC
SR
GBW
t_S
C_S
10kΩ || 20pF load
10kΩ || 20pF load
To 0.1%
f_O = 1kHz
MIN
±3.5
115
96
115
110
+3.6
-3.7
TYP
±120
±150
±80
±40
20
40
4
7
1.5
2.4
2.6
1.2
+3.7/
-3.8
130
103
122
120
+3.7/
-3.8
35
4.5
28
1.3
135
MAX
±250
±320
±150
±80
UNITS
µV
nA
nA
kΩ
MΩ
pF
2.4
nV√Hz
4.0
pA√Hz
V
dB
dB
dB
V
mA
V/µs
MHz
µs
dB
2 _______________________________________________________________________________________