MAX354 Datasheet, PDF (2/12 Pages) Maxim Integrated Products – Fault-Protected Analog Multiplexers

Fault-Protected Analog Multiplexers
ABSOLUTE MAXIMUM RATINGS
(Voltages referenced to GND, unless otherwise noted.)
V+ ...........................................................................-0.3V to +44V
V- ............................................................................+0.3V to -44V
V+ to V-...................................................................-0.3V to +44V
Digital Inputs.........................................(V+ + 0.3V) to (V- - 0.3V)
Input Overvoltage with Mux Power On
V+ = +15V ....................................................................... +25V
V- = -15V ............................................................................-25V
Input Overvoltage with Mux Power Off
V+ = 0V.............................................................................+40V
V- = 0V ...............................................................................-40V
Continuous Current into Any Terminal .............................±30mA
Peak Current into Any Terminal ........................................±50mA
Continuous Power Dissipation (T_A = +70°C)
Plastic DIP (derate 10.53mW/°C above +70°C) ...........842mW
Wide SO (derate 9.52mW/°C above +70°C)................ 762mW
CERDIP (derate 10.00mW/°C above +70°C) ...............800mW
Operating Temperature Ranges
MAX35_C_ _ ........................................................0°C to +70°C
MAX35_E_ _......................................................-40°C to +85°C
MAX35_M_ _ ...................................................-55°C to +125°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10sec) ............................ +300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V+ = +15V, V- = -15V, GND = 0V, V_AH = V_ENH = 2.4V, V_AL = V_ENL = 0.8V, T_A = T_MIN to T_MAX, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN TYP MAX UNITS
SWITCH
Analog Signal Range
(Note 1)
(V+ - 40)
(V- + 40) V
Fault-Free Analog
Signal Range
V_COM, V_{NO V+ = +15V, V- = -15V (Note 1)}
-12
12
V
On-Resistance
(Note 2)
R_ON
I_NO = 1.0mA, V_COM = ±10V
T_A = +25°C
T_A = T_MIN
to T_MAX
C, E
M
285 350
450
Ω
500
On-Resistance Matching
Between Channels
∆R_ON
I_NO = 1.0mA, V_COM = ±10V
(Note 3)
T_A = +25°C
T_A = T_MIN to T_MAX
7
12
Ω
15
NO-Off Leakage Current
(Note 4)
I_NO(OFF)
V_COM = ±10V,
V_NO = ±10V,
V_EN = 0V
T_A = +25°C
-0.5 0.01 0.5
T_A = T_MIN ^{C, E -5.0}
to T_MAX
M
-50
5.0
nA
50
COM-Off Leakage Current
(Note 4)
I_COM(OFF)
V_COM = ±10V,
V_NO = ±10V,
V_EN = 0V
V_COM = ±10V,
V_NO = ±10V,
V_EN = 0V
T_A = +25°C
-0.5 0.02 0.5
MAX354 _{TA = TMIN} C, E -25
25
to T_MAX
M
-100
100
nA
T_A = +25°C
-0.5 0.02 0.5
MAX355 _{TA = TMIN} C, E -15
15
to T_MAX
M
-50
50
T_A = +25°C
-0.5 0.02 0.5
COM-On Leakage Current
(Note 4)
V_COM = ±10V,
I_COM(ON)
V_NO = ±10V,
sequence each
MAX354 _{TA = TMIN} C, E -30
30
to T_MAX
M
-200
200
T_A = +25°C
-0.5 0.02 0.5
nA
switch on
MAX355 _{TA = TMIN} C, E -15
15
to T_MAX
M
-100
100
2 _______________________________________________________________________________________