MAX16010 Datasheet, PDF (2/12 Pages) Maxim Integrated Products – Ultra-Small, Overvoltage Protection/Detection Circuits

Ultra-Small, Overvoltage Protection/
Detection Circuits
ABSOLUTE MAXIMUM RATINGS
(All pins referenced to GND, unless otherwise noted.)
V_CC .........................................................................-0.3V to +80V
EN, EN, LOGIC...........................................-0.3V to (V_CC + 0.3V)
INA+, INB-, IN+, IN-, REF, SET ..............................-0.3V to +12V
OUTA, OUTB, OUT.................................................-0.3V to +80V
GATE1, GATE2 to V_CC ...........................................-12V to +0.3V
GATE1, GATE2...........................................-0.3V to (V_CC + 0.3V)
Current Sink/Source (all pins) .............................................50mA
Continuous Power Dissipation (T_A = +70°C)
6-Pin TDFN (derate 18.2mW/°C above +70°C) .........1455mW
8-Pin TDFN (derate 18.2mW/°C above +70°C) .........1455mW
Operating Temperature Range .........................-40°C to +125°C
Maximum Junction Temperature .....................................+150°C
Storage Temperature Range .............................-60°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V_CC = 14V, T_A = -40°C to +125°C, unless otherwise noted. Typical values are at T_A = +25°C.) (Note 1)
PARAMETER
Supply Voltage Range
Input Supply Current
V_CC Undervoltage Lockout
INA+/INB-/SET Threshold Voltage
SYMBOL
V_CC
I_CC
V_UVLO
V_TH+
V_TH-
CONDITIONS
No load
V_CC = 12V
V_CC = 48V
V_CC rising, part enabled, V_INA+ = 2V, OUTA
deasserted (MAX16010/MAX16011),
V_IN = 2V, V_OUT deasserted (MAX16012),
V_SET = 0V, GATE2 = V_CLMP (MAX16013/
MAX16014)
0.5% hysteresis, MAX16010/MAX16011
5.0% hysteresis, MAX16010/MAX16011/
MAX16013/MAX16014
MIN
5.5
4.75
1.215
1.21
1.15
TYP
20
25
5
1.245
1.223
1.18
MAX
72.0
30
40
5.25
1.265
1.26
1.21
UNITS
V
µA
V
V
7.5% hysteresis MAX16010/MAX16011
MAX16010TAA/MAX16011TAA
1.12 1.15 1.18
0.5
Threshold-Voltage Hysteresis
MAX16010TAB/MAX16011TAB/
MAX16013/MAX16014
5.0
%
SET/IN_ Input Current
IN_ Operating Voltage Range
Startup Response Time
MAX16010TAC/MAX16011TAC
SET/IN_ = 2V
t_START V_CC rising from 0 to 5.5V
7.5
-100
+100
nA
0
4
V
100
µs
IN_ to OUT/SET to GATE2
Propagation Delay
t_PROP
IN_/SET rising from (V_TH - 100mV) to
(V_TH + 100mV) or falling from (V_TH +
100mV) to (V_TH - 100mV) (no load)
2
µs
OUT_ Output-Voltage Low
OUT_ Leakage Current
V_OL
I_LEAK
V_CC ≥ 5.5V, I_SINK = 3.2mA
V_CC ≥ 2.8V, I_SINK = 100µA
OUT_ = 72V
0.4
V
0.4
V
500
nA
2 _______________________________________________________________________________________